Odell and Gawthrop partnership

J.H. & C.S. Odell, East Hampton, Connecticut, Opus 647
St. Ann’s Roman Catholic Church, Nyack, New York
The picturesque village of Nyack is situated on the western bank of the Hudson, less than 20 miles north of Manhattan. Home to 19th-century realist painter Edward Hopper, the village was perhaps better known for its sandstone quarry and as a locus of shipbuilding. These industries declined after 1900, though there was renewed shipbuilding activity during the world wars, with submarine chasers being built there as late as 1948. In the postwar years, the completion of the Tappan Zee Bridge contributed to significant growth in population and commerce. The village underwent a major urban revitalization project to commercialize the downtown area and to expand its economy in the 1980s; today the village center is home to many new business establishments.
I took note of this downtown revitalization when I first visited St. Ann’s Church on a warm spring day in 2006. I had been contacted by Jennifer Pascual in her capacity as chair of the organ committee for the New York Archdiocesan Music Commission. Several weeks prior, Dr. Pascual had asked that I meet with the staff of St. Ann’s, survey the organ, and make recommendations.
On entering the building, to my delight I discovered a well-appointed church sanctuary with terrazzo floors, high ceiling, and best of all, an organ located in the gallery on the central axis. Finally a room that we could work with instead of against! I quickly set about my work, dutifully examining the pipe organ.
Little is known about the life and work of Francis John Newton Tallman, a builder who, according to David A. Fox’s A Guide to North American Organbuilders, based his operations in Nyack from 1894 to 1903, during during which time the organ for St. Ann’s was built. In addition to his organ factory, Tallman also maintained a music store in Nyack village. Prior to life in Nyack, Tallman was employed by the Roosevelt firm, and when he left Nyack in 1904 he reportedly relocated to Brooklyn to work with Reuben Midmer.
The organ Tallman built for St. Ann’s was originally a two-manual instrument with mechanical action, and of his surviving instruments, St. Ann’s was purportedly among the largest. There was evidence that the original keydesk was situated en fenêtre; the panel that replaced the keydesk’s entry point into the case was without the lancet molding treatment found in the rest of the case, as well as being from an entirely different species of wood. The interior layout of the organ suggested a backfall action had been employed for the Great, with squares and trackers for the Swell. The Pedal was divided, on ventil chests.
In the 1930s, the organ’s action and winding system were removed by local service people as part of the process of introducing the organ to the benefits of electricity. Pneumatic pulldown systems were connected to the slider chests, with a similar arrangement for the Pedal, though the ventil system was retained. The organ continued this way until the 1960s, when a supply house console was installed by well-known New York organ man Louis Mohr (also a former Roosevelt employee). Thereafter some minor changes were made to the specification, but otherwise the original pipework survived intact. Apart from decay and neglect, most damage to the metal flues was from “aggressive” cone tuning. Even with the mechanical alterations, tuning access was difficult. When I inspected the organ, most of it, save for a portion of the Great, was inoperable.
As we often restore 19th-century pipework, there were few surprises. Scaling and voicing of flue pipes were very much in line with our own 19th-century practices. While restoration and remedial voicing work were certainly required, in general workmanship we saw little to improve upon. From a modern tonal standpoint, the only serious deficits were in the Swell, which lacked an Oboe and an undulating rank of any variety. Certain ranks—such as the Swell Diapason 8', Salicional 8', and Bourdon 16'—omitted bottom octaves as was often the custom with smaller instruments of this vintage. The Pedal division was spare, but the basics were in evidence, with a suitably scaled Open Wood and Bourdon.
Mechanically, things were far less clear cut. The collection of cone-valve style regulators that replaced the original winding system were arranged in a way that frustrated access to the mechanism. They were also not terribly well built. The slider chests and the pulldown systems installed were all in very bad shape. Both manual chests had runs and frozen sliders. With so many changes of questionable provenance, we felt it was best to save the case and pipes and start over.
With this as a departure point, the members of the Archdiocesan Organ Committee requested we consider some additions. The possibility of the use of digital voices was discussed, though we made clear our preference for a pipe-only design, concentrating instead on filling out a more conservative two-manual specification rather than stretching the limits for a three. Our proposal was accepted, and design work commenced in the fall of 2006.
The mechanical design of the organ is entirely new from the ground up: new conventional wind reservoirs and windchests, all of our own design and construction. We designed and built a new Swell enclosure to accommodate our additions to the division. We also constructed a new two-manual console using our popular terrace-jamb design in quarter-sawn white oak, incorporating a solid-state capture and control system with our standard complement of accessories and relief carving for the music desk.
The Great division of the organ is unchanged but for the addition of a principal-scaled Seventeenth to fill out the chorus. In the Swell, the Bourdon 16' has been made full compass with a bottom octave built and scaled in our shop to precisely match its 8' octave. The Diapason 8', which originally shared a stopped bass, now has its own bottom octave. Other additions to the Swell include an entirely new Oboe (available at 16' and 8'), a GG-compass Celeste, a new 2' Flute and Mixture III based on 2' pitch. Additions to the Pedal include extending the Great Trumpet with a new 16' octave and a fully independent Principal 8'.
Members of our staff who contributed to this project include: Edward Odell (mechanical design, console), Holly Odell (flue voicing), shop foreman John Williams (windchests, reservoirs, pipesetting, electrical), Curt Goettlich (finishing, wooden pipe fabrication, cabinet work, expression enclosure), Stewart Skates (metal pipemaking and repair), and Tristan Bowen, with assistance from Richard Hamar and William Harper. Reeds were voiced by Sam Hughes.
We are grateful to the Archdiocesan Music and Building Commission, as well as the staff of St. Ann’s Church, especially Father Robert Henry and George Bryant, for the opportunity to create something of lasting musical beauty for this parish.
—Edward Odell
J.H. & C.S. Odell

During this bicentennial year of the Archdiocese of New York, St. Ann’s Church in Nyack, New York is blessed to have a newly renovated pipe organ. I had the privilege of playing this organ prior to its renovation, as the winner of the George Bryant Scholarship, which was used towards continuing organ education. Mr. Bryant is the current director of music and organist of St. Ann’s Church, and this parish is lucky to have such a dedicated and talented musician leading its liturgical music program.
Prior to its renovation, the organ at St. Ann’s had many problems; there were many dead notes, missing pipes, and the overall tone was in need of serious remedial work. The console, installed in the 1960s, was also problematic: many pistons were non-functional and there were dead contacts everywhere. Even if the organ itself were in better condition, the console limited the ability to control it effectively.
Director of music, George Bryant, and the pastor, Fr. Robert Henry, saw the obvious need to renovate this instrument, which has served the parish for over 100 years, but had never had a comprehensive rebuild of any kind. After contacting the Archdiocesan Building Commission and Music Commission and taking the necessary steps to proceed with such an endeavor, St. Ann’s Church awarded the contract to renovate the organ to J.H. & C.S. Odell.
After making his survey, Edward Odell listened to the needs of St. Ann’s parish and submitted his proposal. Working with the pastor and organist of St. Ann’s, members of the organ committee for the New York Archdiocesan Music Commission reviewed the proposal as well as vetting proposals from other builders.
The ongoing mission of the New York Archdiocesan Organ Committee is to ensure that the pipe organs of the archdiocese are properly cared for. In our work, we use our combined knowledge and experience to advise pastoral staff who are in need of guidance with regards to their instruments. This committee consists of Meredith Baker, director of music at Holy Trinity West Point, New York; Christopher Berry, director of music at the North American College in Rome, Italy; Daniel Brondel, director of music at St. Malachy’s Church/The Actor’s Chapel, New York City; Jared Lamenzo, director of music at Old St. Patrick’s Cathedral, New York City; and Lawrence Strohm, organist at St. Phillip the Apostle, Pasadena, California, with myself as chair.
Throughout the organ renovation project for St. Ann’s Church, Edward Odell has been in touch with everyone every step of the way, giving detailed updates, sending pictures, and giving honest suggestions when unexpected discoveries came up. It has been my observation that attention to detail and highest quality outcome is of the utmost importance to everyone of the Odell organ firm. Edward and his staff are meticulous craftspeople; it is clear they bring dedication, concern and skill to their work and desire to deliver only the best results.
It should be noted that over the last 150 years, J.H. & C.S. Odell has built many of the organs housed in churches in the Archdiocese of New York, a good number of which still serve their parishes today. Their reputation as builders of fine instruments has existed for five generations, and their work today continues to support liturgical and concert music in the archdiocese. It pleases me to say St. Ann’s Church is now fortunate to be among the fraternity of churches that house the fine work of J.H. & C.S. Odell.
—Jennifer Pascual
Chair, New York Archdiocesan Organ Committee

J.H. & C.S. Odell
Opus 647
St. Ann’s Roman Catholic Church, Nyack, New York

GREAT
8' Open Diapason existing, restored, common metal from 4' C 61 pipes
8' Viola di Gamba existing, restored 61 pipes
8' Doppel Flute existing, restored, wood 61 pipes
4' Principal existing, restored, common metal 61 pipes
4' Chimney Flute existing, restored, common metal 61 pipes
22'3' Twelfth existing, restored, common metal 61 pipes
2' Fifteenth existing, restored, common metal 61 pipes
13'5' Seventeenth new, matching scale, common metal 61 pipes
8' Trumpet existing, restored and revoiced 61 pipes
Chimes new 21 tubes

SWELL Expressive—in reconfigured expression chamber
16' Bourdon new, extension 8', custom matching scale 61 pipes
8' Open Diapason existing, restored with new bottom octave 61 pipes
8' Stopped Diapason existing, restored 61 pipes
8' Salicional existing, restored with new bottom octave 61 pipes
8' Voix Céleste new, GG compass, 55% tin to 4' C 54 pipes
4' Violina existing, restored 61 pipes
4' Harmonic Flute existing, restored, harmonic at middle C 61 pipes
2' Harmonic Piccolo new, matching scale to 4', harm. at middle C, 55% tin 61 pipes
III Mixture new, 15-19-22 183 pipes
16' Bassoon new, dual taper resonators, tapered shallots 12 pipes
8' Oboe new, dual taper resonators, tapered shallots, 49 reeds 61 pipes
8' Trumpet from Great —
Tremulant

PEDAL
16' Open Wood existing, restored 32 pipes
16' Bourdon existing, restored 32 pipes
8' Octave new, zinc to 4' G, remainder 55% tin 32 pipes
8' Gedeckt new, extension Bourdon 16' 12 pipes
4' Choralbass new, extension Octave 8' 12 pipes
16' Trumpet new, matching scale to 8', tapered shallots 12 pipes
16' Bassoon from Swell —
8' Trumpet from Great —
4' Clarion from Great —

Mixture composition
1 to 25: 15-19-22
26 to 44: 12-15-19
45 to 61: 8-12-15

12 general pistons, 6 per division
12 toe studs with black porcelain heads in raised, curved, wooden bolsters
32 levels of capture memory
12-step transposer
MIDI interface, record and playback
Programmable sforzando and crescendo

Couplers and accessories
Great to Pedal 8 (reversible)
Great to Pedal 4
Swell to Pedal 8 (reversible)
Swell to Pedal 4
Great to Great 16
Great Unison Off
Great to Great 4
Swell to Great 16
Swell to Great 8 (reversible)
Swell to Great 4
Swell to Swell 16
Swell Unison Off
Swell to Swell 4

Anabel Taylor Chapel
Cornell University Baroque Organ
Ithaca, New York
GOArt / Parsons / Lowe

Selection
In 2003 Cornell University began planning for a new Baroque organ that would complement the existing Aeolian-Skinner organ in Sage Chapel (Opus 1009 III/68, 1940), as well as other smaller instruments located on campus. The decision was made to place the new instrument in an enlarged rear gallery, constructed with heavy timbers, in the intimate acoustic of Anabel Taylor Chapel. The new Baroque organ would be built by the Gothenburg Organ Art Center (GOArt), part of Gothenburg University in Gothenburg, Sweden, under the primary leadership of researcher and organbuilder Munetaka Yokota. This would not merely be an organ in “Baroque style,” but as much as possible, a reconstruction of an organ that could have been built in the late 17th or early 18th centuries by the German builder Arp Schnitger. The organ that Schnitger built in 1706 for the Charlottenburg Schlosskapelle (Palace Chapel) in Berlin was used as the primary model. This instrument is unique in that it blends the usual characteristics of Schnitger’s instruments built for the area around Hamburg (northwest Germany and the Netherlands), and characteristics of instruments in eastern and central Germany similar to what Johann Sebastian Bach would have known. It was also a sizable instrument for the Palace Chapel in which it stood.
The Charlottenburg organ was unfortunately destroyed during World War II, but there are recordings of the organ in addition to several photographs and documentation data, which allowed GOArt to use the original organ as a model. Because the Charlottenburg organ was confined in an unusual space, it was decided to follow a different model for the case design. The organ built by Schnitger in 1702 for the church of St. Salvator in Clausthal-Zellerfeld was chosen as a model for the case. Although its mechanism has been replaced several times since, the original Schnitger case is still in existence.
During the planning for this project, it was also decided to research how Schnitger built instruments in a city that was some distance from his home in Hamburg. This prompted GOArt and Cornell to enlist cabinetmaker Christopher Lowe of Freeville, New York, and Parsons Pipe Organ Builders of Canandaigua, New York, as local collaborators on the project. GOArt would design the organ, make the pipes, and build the keyboards, pedalboard, music rack, and bench, and provide all of the blacksmith work. Chris Lowe would construct the case, moldings, and balcony structure, and Parsons would build all of the internal mechanism: bellows, foot pumping mechanism, wind trunks, sperrventile, tremulant, key action, stop action, and windchests. The Parsons firm, Chris Lowe, and Munetaka Yokota would all work together to install the completed organ once the organ was set up and tested at Parsons’ Canandaigua workshop.

Parsons’ participation
Each new project brings its own set of challenges, and when a project involves three primary collaborators working for a university that demands perfection, those challenges could become overwhelming. However, working carefully through each new challenge, the final result speaks for itself as to the dedication to quality brought by each party.
One of the first challenges that we were presented with was the process of communicating design drawings. The design team in Gothenburg created a 3D CAD model of the organ. This model could be imported to our own 3D software, enabling us to measure components and create our own supplemental technical drawings. Three-dimensional computer modeling provides us with a greater sense of how all of the components relate to each other, allowing us to look at any combination of components and to rotate the computer model, and examine it from many angles. This was especially useful during this project, as this construction style was new to our staff and different from that to which we were accustomed.
Although the communication of CAD files across platforms provided challenges, other modern forms of communication were invaluable to this project, and are something that we guess Schnitger might have appreciated if it had been available to him. The use of Internet video conferencing allowed us to demonstrate and ask questions about specific shop techniques while allowing us to watch as Munetaka addressed these questions through demonstration, sketches, and gestures. These calls became daily occurrences during the latter part of the project and were crucial to its success.
This project was to be a “Process Reconstruction”—a term coined by the GOArt research team to describe the method used to discover unknown construction techniques, through the process of actually building the organ, rather than just through scholarly discussion. In other words, sometimes we cannot know the specific process or the correct way of building a component until we have experimented. In the end, this required us to learn many new skills and gave us an appreciation for the process that we may not have otherwise known.
The use of woodworking techniques consistent with the period was essential for the project’s success. We were permitted to use power equipment to mill lumber and cut it to size, but the final surface needed to show the traces of hand planing and scraping. As modern woodworkers, we are more likely to reach for our router or palm sander than for our hand plane. The necessity of using hand planes and scrapers in this project has re-trained us to reach for those tools and complete the task at hand before we could have gotten the router set up. The organ is made entirely of quarter-sawn white oak. This construction style relies heavily on joinery, some nails, and some glue. Long nails, ranging in length from 4 to 5 inches, were hand-forged by a blacksmith in Sweden, along with all the other ironwork required for the key and stop action, the bellows pumping mechanism, and the casework hinges and locks. Leather was provided by a German supplier, using period tanning techniques.
The key and stop actions are made in a manner consistent with Arp Schnitger’s practice. The key action rollers are made of white oak. Key action squares are made of iron and were supplied by GOArt. Most trackers and stickers are made of white oak, and the ends are hand wrapped with twine for strength. All metal trackers are of brass wire, and all trackers and stickers have hand-bent brass wire ends inserted. The key action is suspended, which means that the keys pivot at the tail and hang from the trackers or rest on the stickers from the chest. The Manual key action travels up from the key to the rollerboard, which is nailed to the back frame of the organ. The Rucwerk keyboard pushes stickers that carry the action to a rollerboard, which is located under the organist. The Pedal key action also relies on stickers that transfer motion to a rollerbox, which carries the motion, via trackers rather than rollers, to the Pedal chests on either side of the organ.
The stop knobs are made of pear that has been dyed black, with a bone button in the center. The stop action traces and trundles are made of white oak, with iron arms and levers. The iron arms are heated red-hot and then pounded into the oak trundles and are secured by quickly peening the iron.
The organ is winded from four large wedge bellows located in an isolated room in the tower of Anabel Taylor Chapel, approximately 30 feet above and behind the organ. The bellows can be foot pumped, or an electric blower can be used for practice without an assistant. Solid oak windlines connect these bellows to the organ. Windlines are joined with splines or inserted with tenons, and all joints are sealed with leather. A single Schnitger-style tremulant affects the entire organ.
Five windchests are located throughout the organ. The Manual and Pedal each have two chests, and the Rucwerk has one. All of the chests are built of solid quarter-sawn white oak. Given the wide humidity swings common to New York State, leather slider seals are used to eliminate runs and provide consistent wind to the pipes through changing climatic conditions. This required that each individual toeboard be carefully shimmed to allow the sliders to move with the correct freedom.

Casework
The casework was made by Christopher Lowe and Peter DeBoer in Chris’s workshop outside of Ithaca, New York. As the parts were made over an eleven-month period, they were assembled in a nearby barn. The case is made almost entirely of quarter-sawn white oak, mostly domestic. The oak in the long pedal tower frames and the thick posts at the console sides was imported from Germany. The rear panels are made of unfinished pine. Traditional joints hold the frame together: dovetails, splines, and pegged mortise and tenon. The panels are held together with clenched wrought-iron nails and have hand-forged iron hinges where access is needed for tuning. The molding profiles taken from the Schnitger organ in Clausthal-Zellerfeld were smoothed with an array of old wooden molding planes and custom-made planes and scrapers.
When Chris asked for guidance on what the finished surface of the moldings should be like, Munetaka responded, “We want to see the tool marks . . .
but they have to be nice tool marks.” The insides of the panels are finished with an extra deeply scooped texture for its acoustic property. All the oak has been fumed with ammonia to darken it, and the exterior surfaces were rubbed with linseed oil with iron-oxide pigment. The pipe shades are of basswood scroll-sawn to leafy shapes, and were painted by Joel Speerstra and his mother, Karen, with shadows and details to appear three-dimensional.
The casework was dismantled from the barn and moved to our Canandaigua workshop in November 2008. The interior components were installed over the next year, and the entire organ was enclosed in a tent and fumed with ammonia. Following this process, three wooden stops were installed for testing, and the organ was featured in an open house event at our facility on January 10, 2010.

Installation
Installation of the organ began in February 2010. This process required more on-site construction than to what we are accustomed. Because the pipes were shipped directly to Cornell University, the racking process had to be completed on-site. This required burning the rack holes to the correct size, for each pipe, in a tent outside the chapel in the frigid February air. The various tapered irons were carefully heated in a hand-crank coal forge; monitoring the exact temperature of the irons was critical to the process. Once ready, the irons were used to enlarge the holes by burning the wood until the pipes fit correctly. All of the upper racking was performed on-site, with the façade pipes being carefully carried up the scaffold to be marked for the precise location of the hook. Once soldered, a pin was located and driven into the oak rack.
All of the pipes that are offset from the main chests are conducted with lead tubes that were individually mitered, soldered, and fit on-site, and forced into leathered holes in the toeboards.

Pipework
The majority of the pipes in the organ are combinations of lead and tin. The wooden stops are made of pine. The pipe metal was cast on sand, as it would have been in Schnitger’s time. This technique was “rediscovered” by GOArt as part of their original research project in Gothenburg. In contrast, the modern method of casting thick metal sheets and then planing metal to the desired thickness by machine, produces a weaker material because it removes the hardest metal from the outer surface.
As Munetaka Yokota notes,

If the handcraft worker has to do everything by hand, then she or he will have the incentive of casting it as close as possible to the desired thickness and with the desired taper, and scraping it minimally, but very carefully, in the areas where it must be scraped well for acoustical reasons. This much more complex process works with the metal to create a sheet that gives a structural and acoustic result that, almost as a byproduct of the process, is as close as possible to the original Schnitger pipes. . . . Process reconstruction was developed with the goal of reproducing the acoustical quality of the 17th-century organ pipes, and this . . . philosophy is applied to the rest of the organ production as much as possible.

Final product
The organ was publicly presented during the Organ Inauguration and Dedication Festival and Conference, March 10–13, 2011 on the Cornell University campus. Many lectures were presented detailing the world that existed when the original organ at Berlin’s Schlosskapelle was introduced in 1706. There were demonstrations of the organ’s individual stops and a discussion about the construction process, and numerous concerts to demonstrate the organ as a solo instrument as well as how it worked together with other instruments. The inaugural concert by Harald Vogel was presented twice to allow more people to experience the new instrument in the intimate space of Anabel Taylor Chapel. The first inaugural concert also featured the new composition Anacrusis by Kevin Ernste. This piece featured the organ with electronic sounds as well as live organbuilding sounds made by numerous students and organbuilders who had worked on the instrument.
We would like to thank Professor Annette Richards, University Organist, who was the impetus behind this project and the glue that held it all together. Professor David Yearsley also provided welcome support and encouragement throughout the project. The support of Jacques van Oortmerssen, who served as inspector for Cornell during the project, was crucial to its success, and his performance during the festival was a tribute to his contributions.
The artistic endeavor of building the organ now gives way to the artistic endeavor of using it to teach and to enrich the lives of people for generations to come. For Parsons Pipe Organ Builders, there is a single underlying purpose to creating these beautiful instruments: that this organ will be used by Cornell students to glorify God through weekly services of worship.
—Parsons Pipe Organ Builders
4820 Bristol Valley Road
Canandaigua, NY 14424-8125
888/229-4820
www.parsonsorgans.com

To view a descriptive video produced by Cornell University, visit <http://www.cornell.edu/video/index.cfm?VideoID=1017&gt;.

Parsons’ staff:
Richard Parsons
Calvin Parsons
Duane Prill
Peter Geise
Aaron Feidner
David Bellows
Glenn Feidner
Graham Sleeman
Jay Slover
Matthew Parsons
Steven Martindale
Tony Martino

Photo credit: Timothy Parsons, unless otherwise indicated

Anabel Taylor Chapel
Cornell University Baroque Organ
Ithaca, New York
GOArt / Parsons / Lowe

MANVAL (II)
1 PRINCIPAL 8 fus
2 QVINTADENA 16 fus
3 FLOITE DVES 8 fus
4 GEDACT 8 fus
5 OCTAV 4 fus
6 VIOL DE GAMB 4 fus
7 SPITZFLÖIT 4 fus
8 NASSAT 3 fus
9 SVPER OCTAV 2 fus
10 MIXTVR 4 fach
11 TROMMET 8 fus
12 VOX HVMANA 8 fus

RVCWERK (I)
1 PRINCIPAL 8 fus
2 GEDACT LIEBLICH 8 fus
3 OCTAV 4 fus
4 FLÖITE DVES 4 fus
5 OCTAV 2 fus
6 WALTFLÖIT 2 fus
7 SEPQVIALT 2 fach
8 SCHARF 3 fach
9 HOBOY 8 fus

PEDAL
1 PRINCIPAL 16 fus
2 OCTAV 8 fus
3 OCTAV 4 fus
4 NACHT HORN 2 fus
5 RAVSCHPFEIFE 2 fach
6 MIPTVR 4 fach
7 POSAVNEN 16 fus
8 TROMMET 8 fus
9 TROMMET 4 fus
10 CORNET 2 fus
(preparation)

TREMVLANT
VENTIEL MANVAL
VENTIEL RVCWERK
VENTIEL PEDAL
CALCANT

Four wedge bellows

Pitch: a1 = 415 Hz
Compass: Manuals C, D–d3
Pedal C, D–d1
Temperament: Werckmeister III

The stop names are presented as on the stop labels. Note that the “x” has been replaced by a “p” in both the Rucwerk Sepquialt and Pedal Miptur, possibly as a nod to the division names Rückpositiv and Pedal.

30 stops, 40 ranks, with one preparation.

J.H. & C.S. Odell Opus 645

United Methodist Church of Westport and Weston,

Westport, Connecticut

From the builder

I first looked over the 1968 Angell pipe organ at the United Methodist Church of Westport and Weston in the winter of 2005, having been recommended to the church by our friend K. Bryan Kirk. What we found in Westport was an organ with many pipes that were well made, but in some cases unusually constructed and, by our standards, only roughly voiced. The flue pipes were made mostly with a high content of tin. We suspect Tim Koelewijn was the original pipemaker. Just about everything else in the organ had been made by domestic and foreign supply houses. Overall, quality varied widely. Some things were very neatly done.

Though by our standards not altogether under-scaled, the organ did suffer in just about every other way from the prevailing trends of the era when it was built. Wind pressures were low: less than two inches in the Great and three in the Swell. Looking at the original stoplist, we noted that none of the choruses in the organ were complete, though the organ did boast two Célestes and a triple-overblowing Zauberflöte. The reed complement for the organ consisted of a double-blocked French style 8’ Trompette (extended to 16’ in the Pedal) and a 4’ Rohr Shalmei.

The windchest mechanism was a problematic plunger-type solenoid system that had been giving trouble for years. The console was a veneered plywood supply house unit already years beyond its life expectancy. The open contact switching system was dispersed throughout the organ; some of its components had already failed. The wind supply for the entire Great division was provided by a single 18≤ by 24≤ reservoir whose internal volume was largely dedicated to its curtain valve.
After an initial tuning of the organ, the church’s new music director and organist, Todd Simmons, pressed me as to what could be done to make the organ better. I pointed out that the organ had mechanical and tonal issues, to be sure, but there was something to work with here, some raw material, which with proper attention could be the basis for a good pipe organ. In my wife Holly’s words, the existing pipework possessed “unrealized potential.”

Weeks later we met with the trustees to present our findings, expecting that at some point in the future funds could be raised to finance the organ project. One can imagine my surprise when Mr. Simmons called me a few weeks later to say that a single anonymous donor had stepped forward. How soon could we start? Thus we found ourselves sweating in the summer heat on a stretch of days the following July, packing and removing the pipes that would become the basis for our Opus 645.
In the design process we developed a new specification with input from K. Bryan Kirk. We instinctively sought first to meet the essential requirements of a liturgical instrument, something we believe to be utterly crucial, especially in the case of smaller pipe organs. Given the limited space for the organ, we felt a two-manual scheme with few frills would be best. We resisted a request for digital augmentation, instead focusing on a design that would be pipe only.

Certain early decisions seemed obvious. Given the dry acoustic of the church, the baseline scale of the Great chorus needed to be increased. This chorus was also completed with the addition of appropriately scaled new pipework from 22⁄3’ pitch upward. The cutup schedule of the existing Great capped flute was raised, arched, and the stop entirely revoiced. A new independent 4’ Harmonic Flute (based on the unique and very successful scale found in our historic Opus 178 at St. Charles Borromeo in Brooklyn) was constructed and voiced. Over the course of the project nearly every zinc pipe in the organ made its way through our pipe shop: frozen metal caps were freed, tuning inserts and toes replaced, seams and scrolls repaired. Being left in a raw state, many of the zinc pipes had an unsightly powdery white oxidation. We removed this, and gave all zinc basses a sealing coat of varnish to protect them.
The wind pressure of all manual divisions was raised to a more moderate four inches. Holly, then pregnant with our son Caleb, did her usual superb job of revoicing all the other existing and new flue pipework, managing to do so before reaching her final trimester. During this past winter we joked more than once: which would be given birth first, our son Caleb or the organ for Westport?

Where, before, the Great division of the organ had seven ranks, it had now eleven. To provide for this expanded division adequately, we built a new, larger reservoir. The rest of the organ’s wind system was rebuilt and reengineered as the new design required.

In dealing with the Swell division, again certain decisions seemed obvious. The 4’ Rohr Shalmei, only marginally useful, was replaced with an 8’ Oboe, expertly voiced by Sam Hughes. Proceeding as she did in the Great, Holly revoiced all of the existing Swell flues and voiced the new pipework for the Swell flute chorus, which was completed to 13⁄5’ pitch. The existing Trompette was kept, though carefully cleaned up and regulated in a cooperative effort between Sam and Holly.

In our recently expanded East Hampton shop I concentrated on the construction of the console, while our shop foreman John Williams constructed new windchests whose design was first developed for our organ at St. Ann’s in Bridgehampton. The unusually short feet of the 8’ old flute basses made for some interesting pipesetting. New offset chests were provided for everything save the original Pedal Subbass, a mammoth mahogany affair that only needed rebuilding.

The new console was based on our current terrace-jamb design with several embellishments. Improvements on the existing design include a slightly deeper cabinet with an added horizontal stile, raised panel work, additional applied moldings, hand-carved brackets, a two-piece knee panel and solid walnut music desk, the latter being picture-framed with the same quarter-sawn white oak used for the carcass and façade.

The console features an integrated solid-state capture and control system with fully programmable features, MIDI interface, and our standard complement of rear-fulcrum keyboards with basswood levers. The oblique drawknob heads are a reproduction of our 19th-century design. Respected organists who have played it have described our console at Westport as “elegant and comfortable.”
My design of the façade was in part born of necessity. Since both the manual and pedal principal stops were being rescaled, new bass pipes would be required. We naturally needed to make the most of the existing chamber space, and one of the simplest ways to do that was by moving the basses of these stops out into a façade.

Every pipe in the façade is functional. The bass notes of the Great and Pedal principals are polished aluminum, made to our specifications by Matters, Inc. of Hermosa, South Dakota. The pipes are arranged in three towers and two flats and the overall height of the case tops out at 15 feet, mounted roughly 10 feet above the sanctuary floor. The style of the casework is deliberately simple, so as to be in harmony with the appointments of the church sanctuary.

The façade performs a very important function in giving one a visual focal point. It declares the organ present, and urges one to consider it rather than wonder from where behind the grille cloth the organ might be. Its cruciform arrangement also reflects elements of sacred numerology: three towers with three pipes each for the Trinity, ten pipes located within the inner flats for the Commandments.

The sanctuary space in Westport could be described as a postwar-modernist take on the “Akron Plan,” less the adjoining Fellowship Hall. Four sets of pews radiate from the altar and pulpit up front, with organ and choir off to the left. The space over the altar is open with a ceiling height of approximately 35 feet. This intersects with a lower A-frame suspended transversely over the pews. From there the ceiling slopes downward to the rear of the pews to meet a northeasterly facing wall that is mostly glass. The floor is a simple concrete aggregate. Thankfully, carpet was absent. More simply described, it is a space with a great deal of cubic volume, but not overly reverberant.

Throughout the process we gave a great deal of thought to what levels of power would be appropriate for the various tonal resources of the organ. Our concerns about sufficient tonal egress from the chambers were put to rest when we experienced how well the organ spoke into the room. In the tonal finishing process we were pleased to discover how our scaling and voicing decisions suited the space. With a well-balanced variety of 8’ tone available, the organ easily leads congregational singing in a variety of settings.

Overall, we are very happy with what we have achieved in Westport. I would be remiss not to mention others who have contributed to this project: my wife and business partner Holly Odell was responsible for revoicing all existing pipework and voicing of new pipework. John Williams built nearly all the windchests and was responsible for all pipesetting. John and I collaborated on the wind reservoirs and organ case elements. In addition to overall mechanical design and layout, I milled, built and finished the console and casework as well as handling most other finishing duties. Working out of our pipe shop, Stewart Skates handled all pipe repairs. Luc Ladurantaye of Lac Saguay, Quebec, built the new metal pipes to our specifications. Gordon Auchincloss assisted in the wiring and final assembly of the console, and Thomas White assisted in windchest construction and wiring. John Williams, Thomas White, and myself handled the installation. Tonal finishing duties were divided between Holly and myself, with occasional assistance from Richard Hamar and Fred Heffner.

—Edward Odell



From the music director

In my third year as choir director and first year as organist of the United Methodist Church of Westport and Weston, I was introduced to Edward Odell by K. Bryan Kirk, as we were in search of someone local to assume the maintenance of our Angell pipe organ. While I was not dissatisfied with the firm maintaining our organ at that time, I knew it was only a matter of time before a major overhaul was needed, and no one had ever made a complete inspection and report on our instrument. Given the current condition of our organ, I felt comforted in knowing someone local could resuscitate it at a moment’s notice.

After a thorough tuning and evaluation of the organ, I was encouraged by Mr. Odell’s report that although there were serious electrical and tonal issues present, the pipes themselves were well made and could be repaired and voiced (apparently for the first time ever) if we had the means to fund an organ project. Having just completed a fund-raising campaign for a new grand piano, our church did not have extra money to start an organ building fund-raiser, and we felt uncomfortable asking the congregation to dig into their wallets again so soon. This was discouraging as we knew that time was close at hand; in recent years our organ had become increasingly undependable.

Not long after we began exploring these issues, it happened one Sunday morning that the entire organ pedalboard suddenly made itself unusable. Having little alternative, I decided to play that morning’s service on the piano. This coming just a few weeks after Mr. Odell’s presentation to our trustees, there was (understandably) a certain degree of panic, since we were totally unprepared financially to fund an organ project this soon. Even though our organ was one of the longest surviving Angell pipe organs in the area, we had hoped (and expected) it to last longer. It was more and more apparent that something had to be done soon. Before we even had a chance to strategize, I received a call the next day from the pastor informing me that a donor wishing to remain anonymous had left a very large check on his desk with the intention of funding the organ project.

As has been elsewhere stated, our previous instrument suffered from a lack of tonal finishing and the pipes themselves had never been voiced properly. The pipes being of relatively small scale, we were used to a thin, shallow sound that did not possess enough power to adequately fill our worship space, even when I registered full organ. At the start of the project, I had doubts as to whether any new organ would be strong enough, given the room’s difficult acoustics and the location of the organ chambers. Mr. Odell assured us that once the new organ was installed, we would be amazed at the difference.
One of the most impressive enhancements with the new organ, aside from the exquisite façade, is the quality of sound as well as the power behind it. We now have an instrument that adequately leads our congregation in singing, as well as providing full, but subtle, accompaniment for the choir anthems. I can honestly say that at every step of the way, Mr. Odell and his firm have not only met but exceeded my expectations with our new organ and have gone above and beyond the call of duty to deliver an instrument that is even better than the original proposal stated.

It is a testament to his excellent work that not only do the trained musicians in the congregation appreciate this new pipe organ, even the untrained listeners have noticed a huge improvement over the previous instrument. One member (who at one time happened to be unsupportive of the project) admits that now she could not imagine our service without a pipe organ. The church is well pleased, as am I, and we celebrate at every Sunday service this work of art courtesy of the firm of J.H. & C.S. Odell.

—Todd Simmons, organist and music director, United Methodist Church of Westport and Weston



From the consultant

When I began teaching in 1988 at a music school in Westport, Connecticut, I was naturally curious about local pipe organs. Over the years, I became more familiar with the organ at a nearby church: the United Methodist Church of Westport and Weston. The instrument was in poor mechanical condition: it exhibited a failing combination action, frequent ciphers, tuning instability and other frustrations, even though periodic maintenance was given. Being a product of its time, it was very thin in sound, had little bass response (as did the room) and few solo colors. Most importantly, there was no sense of real ensemble, even when the tutti was drawn. The instrument was also limited in its dynamic range for choral accompaniment and congregational singing, and was weak when trying to blend with other instruments. Overall, the organ did not make a strong impact.

A few years later a new organist and choir director was hired, Todd Simmons, one of my teaching colleagues from the music school. As the organ continued to deteriorate, he and the church became even more disappointed with the organ’s unreliability and marginal tonal resources. Knowing I had done other consulting work, Todd asked me to work with him and the church regarding the organ. Realizing the inherent problems, both musical and mechanical, we began an in-depth study of what could be done to either rebuild or replace the organ with something that would not only offer more tonal possibilities but also fill the room and excite the strong congregational singing potential we knew was there.

As we talked, it was apparent that virtually a new organ would be the best option, although much of the existing pipework could be retained if it were rescaled, revoiced and placed on a new, reliable chassis. The organ needed to be reliable and have a wider dynamic range, more tonal colors and a strong sense of presence in the room. It had to strongly lead and accompany congregational singing and sensitively render choral, solo and instrumental accompaniment.

From the outset, one of my pervading concerns was the church’s acoustic, which, while fine for chamber music, was a bit dry for organ and choral music and congregational singing. Having noted the difference in the acoustic when the room was more fully occupied, I knew the challenge of filling the room efficiently would be a mandate for the builder.

Our task began to take shape. Meetings were held and candidate builders were vetted. As work continued, a stop-list began to emerge, while we kept in mind budget and space limitations. One of my thoughts was to ask for a façade, as the previous organ had nothing visible but for a console in a lowered pit in the choir area. I reasoned that a façade would reinforce the impression that the church was getting something new, better and different. We agreed from the beginning that the organ should remain an all-pipe instrument.

After naming a few candidates, one firm was clearly the most interested, experienced and willing to work with us and on this organ. Having known the Odells and their fine lineage of historic instruments as well as their excellent work on new organs and various projects over many years, I was happy to welcome their presence.

The church had Edward and Holly Odell give the organ a full tuning and submit a proposal for either rebuilding or a new organ. As the Odells looked through the organ, they determined that a new console, chassis and electrical system would be required, and that it would be possible to rebuild one small windchest, but otherwise new windchests would be required throughout. By adding a façade for visual interest, some new pipework and retaining about half the existing pipework (though carefully rescaled and revoiced), the organ could take on a new character that would be far more flexible and of greater quality than its predecessor. This concept, coupled with their thorough proposal, helped to land them the contract.

As the new organ design was developed, the specification was refined. Among the ideas we discussed was the clever suggestion to borrow the Great 4’ Octave as an 8’ Second Principal stop on the Great, creating a secondary 8’ Principal for smaller combinations. The stop could also be used to fill out foundation tone when needed. As we continued to explore various tonal issues, it was noted that the old organ had no soft reed color or solo flute color. Among other things, Odell suggested adding an 8’ Oboe and building a new Harmonic Flute, patterned after historic Odell examples, but carefully adapted for the flute scales at Westport.

My early recommendations had included new 22⁄3’ and 2’ principal stops to replace the existing flute-scaled 2’ in the Great. The Odells suggested going further to install a new Mixture to create a full Principal chorus, giving the organ a sense of ensemble, a true plenum, something it never had.
Having listened to the result, I can state these stops create a truly full-sounding principal chorus, finally integrating the instrument into the room. The organ as conceived by the Odells has made a huge difference for hymn and repertoire playing and can now “ring the room” more effectively.

The Great also contains the revoiced 8’ Bourdon, now sounding more like a continuo stop, suitable in choral music or to accompany the Swell’s cornet decomposée. The Gemshorn and its Celeste were retained for flexibility in accompanying and providing more soft colors.

The Swell received “the Odell treatment,” in that all the pipework was revoiced. The flues, strings and mutations were all transformed by voicer Holly Odell, and the reeds were reworked to make a dramatic difference. The strings and 8’ Rohrflute now have more presence and can fully support the choir, as well as contribute to the ensemble. The Swell cornet decomposée is now nicely balanced, and the flutes have a more piquant character.

The new 8’ Oboe offers a nice color for softer choral accompaniment and foundation combinations, as well as providing a new solo stop. The existing 8’ Trompette, originally extended to 16’ for the Pedal, was also cleaned, revoiced and regulated into a stop that now serves a dual-purpose chorus/solo reed. The 16’ octave, now reconditioned, adds more gravitas to the Pedal and the full ensemble.
The full ensemble now fills the church worship space with a richer, warmer and well-blended tone. The softer sounds are more usable and possess a wider dynamic range, so the possibilities for choral, vocal and instrumental accompaniment are greatly enhanced.

As a concerned observer, I paid close attention to the project throughout the building process. The Odells always welcomed my inquiries and kept all parties informed with frequent photographs from their shop. Once the installation commenced, it was exciting to see how beautifully designed and well made all components of the organ were, both inside and out. During the tonal finishing, it was gratifying to witness the attention to detail in balancing each stop and the various ensembles. Further, it was refreshing to hear from the builder that materials and workmanship were never an issue; they simply insisted that in every aspect things be done thoroughly, with the highest level of attention to detail.

The organ is now in regular use and a series of dedication concerts have been planned. My thanks go to Edward and Holly Odell, their associates, to Todd Simmons and the United Methodist Church of Westport and Weston, Connecticut, and the donor for having me work with them in a collaborative effort to complete this important project to enrich the worship and outreach of this vibrant congregation.

—K. Bryan Kirk, advisor/consultant

J.H. & C.S. Odell Opus 645

United Methodist Church of Westport and Weston, Westport, Connecticut

Great (Wind pressure 4")

8’ Principal CC–AA en façade, otherwise 70% tin, 61 pipes

8’ Second Principal 1–12 from Principal 8’, 13–49 from Octave 4’

8’ Bourdon 70% tin, arched cutup, 61 pipes

8’ Harmonic Flute 1–12 from Bourdon 8’, 13–61 from Harmonic Flute 4’

8’ Gemshorn 70% tin, 2/3 taper, 61 pipes

8’ Gemshorn Céleste 70% tin, 2/3 taper, 49 pipes

4’ Octave 70% tin, 61 pipes

4’ Harmonic Flute 55% spotted metal, special Odell scale, harmonic at
middle C, 61 pipes

22⁄3’ Quint 55% spotted metal, 61 pipes

2’ Super Octave 55% spotted metal, 61 pipes

III Mixture 55% spotted metal, 19-22-26, 183 pipes

Chimes. 25 tubes


Swell (Expressive, in existing chamber, wind pressure 4")

16’ Rohr Gedeckt wood, 13–61 from Rohr Flute 8’, 12 pipes

8’ Rohr Flute 70% tin, chimneyed, 61 pipes

8’ Gamba 70% tin, bearded, 61 pipes

8’ Gamba Céleste 70% tin, bearded, 49 pipes

4’ Spitz Principal 70% tin, 2/3 taper, 61 pipes

4’ Flute 55% spotted metal, 2/3 taper, 61 pipes
22⁄3’ Nazard 70% tin, capped and chimneyed to middle C, 61 pipes

2’ Block Flute 70% tin, 61 pipes

13⁄5’ Tierce 55% spotted metal, 2/3 taper, 61 pipes

8’ Trompette double blocked, French shallots, 56 reeds, 61 pipes

8’ Oboe dual taper resonators, English shallots, 49 reeds, 61 pipes

Tremulant


Pedal

16’ Subbass wood, 32 pipes

16’ Rohr Gedeckt from Swell

8’ Octave CC–GG# en façade, otherwise 70% tin, 32 pipes

8’ Bourdon extension, Subbass, 12 pipes

8’ Rohr Flute from Swell

4’ Choralbass extension, Octave 8’, 12 pipes

4’ Flute from Swell

16’ Trompette extension to Swell Trompette, 12 pipes

8’ Trompette from Swell

8’ Oboe from Swell

4’ Clarion from Swell

J.H. & C.S. Odell, East Hampton, Connecticut, Opus 644

St. Ann’s Episcopal Church, Bridgehampton, New York

From the Rector of St. Ann’s

The committee all agreed--something had to be done. For
years the church organ had been in irreversible decline, and the time had come
to act. I regarded this to be a daunting and confusing challenge in which we
needed professional counsel. Dr. Mark Andersen guided us through the various
options and needs of the decision-making process, and by July 2004 it was
agreed that J.H. and C.S. Odell of East Hampton, Connecticut be engaged to
restore the organ. It was a decision that we would never regret.

In September 2004, Edward and Holly Odell arrived to remove
the existing organ. Pipes were carefully laid out in special boxes. Frames and
blowers were removed--and those were only the things that I could
identify! It all happened remarkably quickly, and before long the truck was
driven away leaving a large space where the console had once stood, and a
spotlessly clean church where the disassembly had taken place.

The novelty of using just piano and occasional other
instruments wore off after Christmas, and we waited anxiously for the organ to
return. Our patience was not helped by tantalizing photographs and reports sent
regularly from the Odell factory showing the new instrument taking shape!

It was March 2005 (the day I was flying off on vacation)
that the Odell team returned. It was time to put the whole thing together, but
it was only two weeks before Holy Week, and three to Easter. Could it really be
done?

Eight days later I returned to find the church in wonderful
disarray with parts and pipes everywhere, and Edward Odell looking and sounding
confident, if a little tired. Yes, of course it could be done. The project was
running according to schedule. The organ would be partly voiced by Palm Sunday
and ready for Easter.

Every part was in place and every promise fulfilled. A
magnificent new console was carefully maneuvered into position. Pipes were
ready and being expertly voiced by Holly Odell. Cables and wires were
connected. The organ had life--and was indeed ready for Easter morning. It
was resurrection in a different form!

We have not looked back since then. Not only has this
instrument enhanced our Sunday worship, it has enabled us to host a season of
superb organ recitals over the summer, and earned for St. Ann’s Church a
reputation for being a place where good music can be found.
style="mso-spacerun: yes"> 

Working with the Odell Organ Company has been not only a
proven right decision but also a joy. From the outset we not only admired the
professionalism of Edward and Holly Odell, but also came to share in their love
of organs and sheer depth of knowledge in their field. All these things,
coupled with their warmth and sense of humor, have made the whole process one
which we can reflect on with immense satisfaction. It is never an easy task for
a small parish church to embark on such a large project and investment, but we
know that we have learned and benefited so much from choosing the right organ
and the right builder.

The Reverend Tim Lewis, Rector

St. Ann’s Episcopal Church

Bridgehampton, New York

From the Consultant

As an organ consultant for nearly 35 years, I have had the
opportunity to design a large range of instruments from the smallest two-manual
to several five-manual instruments throughout the United States, England, and
Australia.

St. Ann’s parish is that wonderful combination of
sophistication in a relaxed atmosphere. It is many New Yorkers’ church away
from home, and the organ would have to meet the discriminating tastes of
parishioners who worship in some of the largest churches in the metropolitan
area.

There was not much with which to start--an old hybrid
Möller from the ’20’s that was on its very last legs after having several ranks
replaced over the years. I designed an organ specification capable of
accompanying a proper Anglican service, but in a size and fit that matched St.
Ann’s. After requesting bids from many organbuilders, it was clear that J.H.
& C.S. Odell had the talent to see the task through with outstanding
results. Tonally the organ now fits the space perfectly and is complete enough
in specification to satisfy even the most discriminating organists. The
craftsmanship is superb, and the voicing is clear and clean, leaning beautifully
toward the English tradition. The project has surpassed my expectations.

Mark Andersen, PhD

New Berlin, New York

From the Organbuilder

Our Opus 644 began life as what could be termed a “Heinz 57”
instrument, which is to say it featured a combination of pipes and parts from a
combination of organbuilders and suppliers. The console case and most of the
wooden pipes in the organ date from a five-stop 1927 M.P. Möller instrument,
which was then rebuilt and altered in the early 1970s. It was during this 1970s
rebuild that much of the original pipework was replaced.

As we found it, the organ was a unified instrument of modest
resources, most of them well made if not terribly well looked after. It was
unrefined, but met the basic requirements. In the 1980s a German supply house
Trumpet 8’ and Mixture III (inexplicably, a Zimbel based on 2?3’ pitch) were
added, along with a polished tin Gemshorn that was used to form a façade. The
entire organ was in a single expression chamber to the right of the chancel. The
existing electro-pneumatic unit chests, made from solid mahogany, were in good
physical condition, though the installation made maintenance access difficult
in certain areas.

In July of 2004, Dr. Mark Andersen (organ consultant to St.
Ann’s) approached us with a prospectus that included a rebuild and enlargement
of the organ. In addition to new pipes and new chest work, a new 3-manual
terrace-jamb console was part of this plan.

Dr. Andersen’s proposed stoplist would add a total of nine
ranks to the organ. The scheme had an immediate appeal, as it would expand the
resources of the organ to include a full principal chorus in the Great, as well
as a new 8’ Rohrflute to contrast the existing Chimney Flute in the Swell.
“Fleshing out” the Great with six new ranks allowed us to recast the remaining
resources to work as a mostly independent Swell division. The new scheme would
also extend the existing Trumpet to 16’ pitch to play from the Pedal and add a
small Cornet (a tenor C, 2-rank 12/17 combination, scaled and voiced to match
the new Great flute).

The challenge, of course, was to now somehow fit 19 ranks in
a space that before barely contained eight. Early in the design process it became
evident that much of the precious real estate in the organ chamber could be
reclaimed if the many offset chests for various ranks could be consolidated
onto a new single offset chest that would also provide for the new Trumpet 16’.
We also wanted to ensure the new chamber layout would permit adequate access
for service and, most importantly, tuning. Rebuilding the existing expression
shades and fitting them with new expression controllers made available space
that had been previously occupied by a pneumatic motor with an unwieldy linkage
system.

We developed a new 7’4? diatonic chest scale to accommodate
the new stops and the relocated Gemshorn. The existing Principal 8’ was
carefully revoiced to give it more moderate power, and the new principal ranks
were scaled and voiced to build from this new foundation. The new Great Bourdon
8’ was voiced using a special arch cutup schedule, which lent the pipes a color
that allows the stop to work superbly as both a solo and ensemble voice. The
Swell was given its own new 3-rank mixture based on 2’ pitch, and the existing
Zimbel mixture was recomposed into a more appropriate chorus mixture based on
11?3’ pitch for the Great.

Though the action for the new chestwork was specified to be
electro-mechanical, we milled all windchest toeboards to be no less than one
and one-half inches in thickness. This, along with proper attention to voicing,
successfully offset any pipe speech problems normally anticipated with this
type of action. Our windchests were made from solid poplar, with the exception
of the toeboard for the new Swell Mixture, which was milled from sugar pine.

The new console and case, both entirely of our own design
and manufacture, were milled  in
our East Hampton shop from solid quarter-sawn white oak, and stained and
finished to match existing fixtures in the sanctuary. The console interior
(stop jambs and key cheeks) was milled from solid walnut and finished with
hand-rubbed Danish oil. The façade pipes are polished tin, made to custom
specifications we developed and submitted to our friends at Giesecke. The new
flue pipes were built to our scales by Luc Ladurantaye Tuyatier of Lac Saguay,
Quebec.

Along with the standard complement of accessories, the
console features an integrated control system with multiple memory levels,
programmable crescendo and sforzando, 12-step transposer and MIDI interface for
record and playback ability. The digital Antiphonal division was contracted and
installed separately by Artisan Instruments.

Edward Odell

J.H. & C.S. Odell

Glück New York,

New York, New York

The Church of Our Lady of Loretto, Cold Spring, New York

This historic church, known for its remarkable collection of
stained glass windows, was recently restored, with a new instrument and a
marble chancel floor included in the renewal plans. Under the direction of Fr.
Brian McSweeney, Pastor; Frances Pergamo, Director of Music; and Fr. Richard D.
Baker of the New York Archdiocese, three organbuilders were each invited to
present their vision of an appropriate musical instrument. The smallest and
most stylistically focused proposal submitted, the new Glück organ occupies a
traditional position in the rear gallery to great acoustical advantage. While
the organ looks toward the French orgue d’accompagnement of the 1860s for both
its concept and tonal palette, it is certainly not intended to be a stylistic
copy.

The manual soundboards are placed side-by-side at impost
level, with the Swell to the right, its vertical shutters operated by direct
mechanical linkage. The two large wooden pedal stops stand on their own
windchests behind the organ. The Great organ incorporates some pipework from a
mid-1870s Levi Underwood Stuart organ of undetermined provenance. Interior
metal pipes are of 70% lead alloy, except for the Swell strings, which are of
50% tin. Wooden pipework is of pine and fir. The façade pipes are built with
English bay leaf mouths arrayed in a swag pattern after Gottfried Silbermann’s
façades of the 1740s.

The walnut keydesk en fenêtre sports beveled figured maple
jambs and pao ferro drawknobs. Both pedal and manual accidentals are Brazilian
rosewood. Compasses are 56/30; there is no combination action, but the three
unison couplers are reversible by toe paddles. The case is painted in various
shades of olive, with details in sapphire, ruby, and faux marbre. Architectural
design was by Sebastian M. Glück, who executed the Neapolitan-style angel,
tower finials, and buttress niches, which are suitably polychromed and gilded.
Color photographs may be viewed at the firm’s web site at
<www.glucknewyork.com&gt;.

The structural design and layout are the work of Albert
Jensen-Moulton, general manager of the firm, who was assisted in the
construction of the organ by Dominic Inferrera, foreman. Voicing and tonal
finishing were accomplished on site by Sebastian M. Glück, tonal director. The
organ was formally dedicated in a series of three recitals by Lana Kollath, Dr.
Jennifer Pascual, and the builder.

--Benito Orso

GREAT

8’               Open
Diapason

8’               Open
Wood Flute

4’               Principal

2’               Doublet

8’               Hautboy
(from Swell)

                       Swell
to Great

                       Swell
to Great Octaves

SWELL

8’               Salicional

8’               Voix
Céleste

8’               Stopped
Diapason

4’               Harmonic
Flute

8’               Hautboy

                       Tremulant

                       Swell
to Swell Octaves

PEDAL

16’           Open
Wood Bass

16’           Stopped
Bass

8’               Octave
style="mso-spacerun: yes">  from Great

8’               Hautboy
from Swell

                       Great
to Pedal

Swell to Pedal

                       Swell
to Pedal Octaves

J.H. & C.S. Odell,
East Hampton, Connecticut
Scarborough Presbyterian Church, Scarborough, New York
I remember receiving my first phone call from Scarborough Presbyterian Church in late January 2005. I was delighted to have the chance to become acquainted with this church and with its organ, my own family’s J.H. and C.S. Odell Opus 327, installed in 1894. Six years on, there is much to report.
One cannot help but be immediately taken in by the beauty of Scarborough Presbyterian, both interior and exterior. The church is set along old Route 9 in Briarcliff Manor. Approached from either north or south, the siting of the building (whose exterior is rich with classical elements) blends in gracefully with its setting.
Scarborough Church was a gift from Mrs. Elliott Shepard as a memorial to her husband in 1893. The architects of record for the church were Haydel and Shepard, a short-lived partnership of Stanford White’s nephew, Haydel, and a nephew of Mr. Shepard. Their only other significant building, the Fabbri Mansion on Manhattan’s 64th Street, echoes the neo-classical style of Scarborough Church—briefly called, “Shepard Memorial,” but organized later as Scarborough Presbyterian. A reprint of the dedication announcement from the May 12, 1895 edition of the New York Times includes copious detail of the building’s appointments, which in modern architectural parlance is properly classified as Beaux-Arts:

The main design of the ground plan is a cross, a porte cochere being one of the short arms of the cross, and the pastor’s study the other arm. The church is built of granite rubble, with trimmings of Indiana limestone. The granite is of a pink tinge, which harmonizes pleasantly with the grayish limestone, and the effect is very striking to the visitor.
The height of the tower from the steps to the top of the cross is about 120 feet. The architecture of the exterior is a distinctly American interpretation of the Renaissance idea as it was in the time of Louis XIV. The granite used in the body of the structure was quarried on the estate of Col. Shepard, which is a short distance south of the edifice.
In the three large windows of the main structure, each nineteen feet high, are stained glass designs. Strictly classical treatment has been used in the interior of the building. The main auditorium has a seating capacity of 350, and the Sunday-school room of 150 persons. The floors are of mosaic in the church, and the pews are of carved wood. The building is as near as possible fireproof, as little wood being employed in the construction as circumstances would permit.
The wood-paneled [coffered] ceiling is secured to the entablature by carved wooden corbels. This ceiling is one of the main features of the room. It is made of California redwood. Its side surfaces are enriched with twenty-eight panels, each six feet square, and with carved wooden rosettes in their centers. This design encloses, as in a large frame, a large panel, itself broken up and subdivided into a considerable number of smaller panels. In the center of the ceiling is a great carved redwood cross. The inner walls are of cement, tinted to harmonize with the ceiling.
The choir dome, under which the pulpit is placed, at the end of the church, is paneled with rosettes, and a large skylight admits light from above. The building is lighted at night with electric lights, and the heating is to be in the winter season by hot-air appliances from the basement. Perfect ventilation is secured by means of exhaust flues in the side walls from the floors to the roof. The organ is in the main tower, while the keyboard is under the choir dome.

As the article states, the console was originally placed in the chancel area, leading me to speculate that this organ was likely the first all-electric adaptation of the patented Odell tubular-pneumatic action. In comparison, there are appreciable, if minor, design differences in the primary mechanism employed in the manual chest action used in our Op. 313 at St. Michael’s Church on West 34th Street in Manhattan. That organ, which is presently under our care and slated for major restoration work in 2012, was originally all tubular-pneumatic when it was built only one year prior in 1893. It has been interesting to note the nuance in mechanisms, scaling, and voicing practices of two Odell instruments that were built at nearly the same time.
As one can easily imagine the unwieldiness of playing the gallery organ from the chancel, it is not surprising that the console was later relocated to the gallery. Apart from this, the organ remained largely intact until the first major campaign of rebuilding and revisions began in the late 1980s through the 1990s.
At one time, there had been ambitious plans for the instrument, evidenced in the documentation of the Peterson switching system installed by a prior technician. Most of these plans went unrealized, though the addition of an anachronistic and stylistically questionable “Positiv” division had been carried out. Other changes included additional reed stops in the Swell, as well as evidence of attempts at rescaling, mostly in the principal stops of the Great.
In the meantime, problems of the winding system and mechanism were largely ignored. It was in this state that I first examined the organ at Scarborough in 2005. The Swell chest was then largely non-functional, owing mostly to issues with stuck sliders and pallet actions in need of rebuilding. I quickly realized that not only would a program of full mechanical restoration be needed, but also a careful reversal of many of the tonal changes, if the final result were to resemble anything that would make sense to a properly trained organist.
In addition to the difficulties with the organ, Scarborough was managing a leadership transition, something that is always trying in the life of any parish. The congregation faced this while contemporaneously entertaining bids for the organ project from us and other local firms, as well as considering wholesale replacement of the organ with a new electronic substitute. It was not until I made a detailed presentation to the congregation that we were able to at least keep the latter option off the table.
While we eventually prevailed as selectee for the organ project, there was no appreciable progress in going to contract until the appointment of Kenneth Potter as organist and director of music in 2007. Potter took the position on the condition of the organ’s restoration. This was agreeable to the Session and we were at last able to proceed.
No sooner had Mr. Potter taken the position than he reached out to me, and a lively discussion ensued on how best to revise and restore the organ. Plans at one point had even branched out into an entirely new case design, for which I excitedly prepared several conceptual sketches, but these were later set aside for both practical and aesthetic reasons. With our limited budget, the majority of our work would have to focus on restoration of the pipes, console, and mechanism. Moreover, with limited gallery space and an already richly appointed interior, it was difficult to realize a case design that would match the level of ornamentation or allow for a proper sense of proportion without getting into models that we knew would be far too elaborate. We officially went to contract in late 2007 and set to commence work in early 2008.
Eventually we settled on the design one sees today, which in many respects closely resembles the organ’s 1894 specification. The floating “Positiv” is gone, its Oboe restored and returned to its proper place in the Swell. The Swell Vox Humana was likewise deleted in favor of the Bassoon 16′, though not without some regret. The addition of the Clarion 4′ was kept, though the stop was revoiced in order to be more in scale (in terms of power) with the rest of the division’s reed chorus. Apart from careful tonal finishing and some adjustments to the power of some of the stops, the rest of the division remains as original but for the replacement of the Aeoline with a matched Voix Céleste for the Salicional.
I approached the Great with similar care. In sorting through the pipework in the shop I was able to review (and correct) prior attempts in rescaling and revoicing. Thankfully, the critical backbone stops of the division (the Open Diapason 8′, Gross Flute 8′, Gamba 8′, and Harmonic Flute 4′) had been left mostly untouched. Efforts had been made to re-scale the principal chorus from 4′ upward with limited success: rather than inserting new pipes in the bass and shifting the entire rank upward, pipes from various sources were randomly inserted in the compass of the Principal, Twelfth, and Fifteenth. To the uninitiated this probably seemed a harmless practice, but I was determined to restore some sense of order. Thus we maintained (and in some cases increased) the rescaling, as my experience with Odell scaling practices from this era (as well as my review of this instrument in particular) called for a significant increase in order to balance the power of the stops of the chorus without attempting to “voice around the scale.” Thus I reoriented the prior attempts at rescaling by fabricating new pipes with properly matching 2/7 mouths, using matched common metal (roughly 70% lead) as opposed to the uncharacteristic spotted metal used before. This allowed better control in the adjustment of the power of these ranks as I worked on them in the voicing room.
The other changes to the Great included the addition of the original Swell Bourdon on new unit windchests, so as to be available at 16′ and 8′ pitch. The Dulciana was deleted in favor of a new, matching principal-scaled Seventeenth. This exchange was part of an overall plan to keep a third-sounding rank available in the division, since the original Great Cornet mixture (17-19-22) was to be rescaled and recomposed into a suitable chorus mixture based on 2′ pitch (15-19-22). The original Cornet Mixture in the Swell had been retained, and Ken and I were in agreement that one tierce mixture per organ was more than sufficient.
Apart from these changes, pipe restoration was straightforward. Along with the windchests and console, everything was brought back to our facility and carefully cleaned. Metal ranks went through our pipe shop for repair. Wooden pipes were repaired and pipe stoppers were repacked. But for the Bassoon 16′ in the Swell and the Trumpet in the Great (which I kept for myself to work on), the Swell reeds went to Trivo in Hagerstown for restoration. Broken reed pipes were properly reblocked, tuning inserts were replaced, and shallots, tongues, and wedges were carefully cleaned and refitted as required.
The rebuilding of the mechanism presented several challenges. The manual windchests were essentially Odell slider chests with electro-pneumatic pulldown motors and slider motors. Both chests were completely stripped down to their tables at our facility so they could be evaluated and repaired. Thankfully, re-tabling was not needed, though damage to some of the sliders was so severe that some of them had to be replaced. Unlike modern slider chests (where engineered plywood is used), the bottoms of the Odell chest grids are covered with motor cloth, and the pallet openings are formed by blocking in the channels inside the pallet box and covering the area with a layer of packing leather. All this was restored to match the original configuration, whereafter the grid channels were carefully sized with thinned shellac, as is the custom. It was an arduous, not to say messy process, but the result was the total elimination of the numerous runs and bleeds encountered prior to removal. Finally, the chest pallets were all re-dressed with new felt and leather, and the motor and primary systems rebuilt.
With the slider motor system we faced a particular difficulty: Odell pneumatic slider motors were an innovative design in their day, but they can be fickle. When they work, they work well, but they often grow slow and unresponsive. Knowing this, in the planning stages of the project I seriously considered conversion to an electric slider motor system, but instead held this out as a last resort. The original pneumatic motors were dutifully rebuilt, and after some experimentation I eventually realized a solution: by placing the slider motor assemblies on their own separate wind reservoir and increasing the pressure moderately, I realized two immediate benefits: the slider motion was now swift and sure, and the action of the sliders no longer had any effect on the divisional wind pressure as they were actuated. I owe the inspiration for this concept to my colleague Timothy Fink, who several years ago used a similar approach when he designed his own pneumatically powered slider system (based in part on the Odell design) for the new organ he built for Grace Lutheran Church in Naples, Florida.
As the Pedal division had recently had its action rebuilt, we were free to leave this section alone and concentrate our remaining efforts on the console, winding system, and façade.
Dealing with the winding system was simple. The original massive single-rise reservoir was replaced with four new properly sized Odell reservoirs, one for each division, and the fourth for the aforementioned slider motor assemblies.
The console carcass was gutted and fitted with new, rear-fulcrum keyboards with basswood levers, and the manual compass restored to the original 58 notes. The newer pedalboard was kept. The stop-action rail and stop-action magnets were replaced with a much more reliable Harris tilting-tablet assembly, whose appearance is more characteristic of a traditional Odell console. The interior of the console was fitted with new panels made of sapele. We installed a new, integrated control system with the customary modern feature set.
The façade, which contains the bottom seventeen notes of the Great Open Diapason, was carefully stripped, repaired, and restored. The original zinc tuning flaps were replaced with spotted metal tuning scrolls. I personally handled the preparation and finishing process. A catalyzed base primer that bonds directly to the metal was used as the undercoat, over which I applied specialized metal lacquer mixed with gold flake powder. The result is a richer, deeper gold color that was accented by the application of silver flake lacquer on the pipe mouth inserts.
Our final step was to replace the 1950s-era wall panels below the impost of the façade. The layout was sketched by my wife Susan, who is a classically trained architect. With no cues from me, she intuitively established a rail and stile pattern that picked up on the center point placements of the pipes in the façade, while maintaining symmetry throughout. The panel molding, which required a custom-made set of molder knives, is a duplication of the custom panel moldings used throughout the church. The panels themselves are made from the same sapele used in the console, and are stained to match the existing appointments. Though it is minor, this was a welcome embellishment to the appearance of the organ.
Members of the Odell staff who contributed to this project include: John Williams (chest restoration, new chest, panel, and reservoir fabrication), Stewart Skates (pipe repair, fabrication, and restoration), Scotty Giffen (site, restoration, and assembly work), David Wason (wiring, site, restoration, and assembly work), Douglas Keilitz (site work, tuning, and tonal finishing), and myself (design, planning, wood and metal pipe finishing, voicing, and tonal finishing). Rigging for the removal and reinstallation was handled by our friends at Auer’s of New York City, long known for their skill in handling this sort of work.
We are grateful to the staff and congregation of Scarborough Presbyterian Church for being given the opportunity to restore this instrument and return it to service. I am particularly grateful to Kenneth and Christine Potter (who have become great friends as well as champions of our work), and also the Reverends Chris Iosso, Dae Jung, and Tim Ives, worship and music committee chair Lindsay Farrell, and most especially the late Florence Fletcher, to whose memory the new organ façade is dedicated.
—Edward Odell
East Hampton, Connecticut

It isn’t often that an organist takes a job with the congregation already understanding that the organ needs to be rebuilt, and he gets a significant say in how it gets done. My first decision was to commit what one might call a heresy among organists. I agreed that the organ needed to be reduced in size; we went from 37 ranks to 30. The results speak for themselves, as much of that reduction involved removing redundant ranks, ranks that served no useful purpose.
Prior to the rebuild, the Swell had become almost completely unplayable and been more or less abandoned. We realized the removal of the entire instrument to the Odell shop would be needed. Now rebuilt, the Swell is a wonderful division of great subtlety and color.
It made sense to keep certain additions, but we wanted these additions to form a real ensemble, and for the organ to speak into the room naturally. A fine Clarion 4′ had been added to the Swell. The Bassoon 16′, Cornopean 8′, Oboe 8′, and Clarion 4′ formed a reed battery that we were loath to break up. In order to keep it, the old Vox Humana 8′ had to go. I deeply regretted this loss, but I love the full reed chorus as it is now. The Aeoline 8′ went the same way to make room for the Voix Céleste. There was more than enough pipework left for quiet music, with the very gentle strings, a Stopped Diapason 8′, and a lovely Rohr Flute 4′ of surpassing beauty.
In the Great division, the previous Tierce had been derived from a split slider on the Mixture. It never worked very well, but I felt it was important to have a full Cornet on the Great, so we sacrificed the Dulciana. The Seventeenth that took its place is the only wholly new rank in the rebuild. The Dulciana’s place in the tonal scheme was taken by an 8′ extension of the 16′ Bourdon. I felt that with the three other strong 8′ stops (Open Diapason 8′, Gross Flute 8′, and Gamba 8′) we needed a quiet 8′ flute. This Bourdon 8′ can be coupled with the Gamba 8′ and form a fonds doux, but it also works beautifully alone, or with the Principal 4′ or Harmonic Flute 4′. With all 8′ flue stops on the Great drawn, one has a close approximation of the classic fonds de huit. After rescaling and restoration, the Great chorus is powerful and intense. With the coupling of the Swell reeds, it becomes immense.
In the process of this rebuild, I learned a lot about what stops are truly necessary. As someone who cut his teeth on the Organ Reform movement, I had difficulty understanding a tonal scheme built on generously scaled 8′ stops, with smaller upperwork, or a second manual division without a Principal 4′. In time, I have come to understand this instrument on its own terms. The Violina 4′ really does serve a purpose, and I have come to love the very modest 4′ Rohr Flute in the Swell; it is delicate and very non-intrusive, and I never seem to stop finding uses for it. The Flute 2′ with the Cornet III makes a wonderful sparkle in that division without adding weight. The Oboe 8′, now returned to the Swell, is an excellent addition to the division’s chorus, adding just enough weight to balance the flues. So much for the Swell organs I was previously accustomed to, with their 8′ Gedeckt foundation and blazing upperwork!
It thrills me endlessly to have other organists come in and play. I love to wander around downstairs and listen, often asking what stops they have on. This organ, which sounds immensely powerful in the gallery, is gentle and convincing downstairs—the fullest registration is not overpowering, but rather full, blended, and satisfying.
There isn’t an ugly stop on the entire instrument. Every rank is distinct, beautiful, and makes the listener sit up and notice, whether quiet, mezzo forte, or loud. Nothing is overbearing and the range of color is amazing. Edward Odell has demonstrated great skill as a voicer, taking stops that had been poorly regulated, and restoring, focusing, and adjusting them to create a satisfying, integrated ensemble. He was ably assisted by Doug Keilitz on the tonal finishing.
Let me conclude by saying we are blessed with some of the finest acoustics I have ever experienced in a church, both for organ and choral music. The instrument is now inspiring our choir to new heights. As I had hoped, the wonderful sounds coming from the loft are enhancing our worship and attracting new members.
—Kenneth Potter
Organist and Director of Music

J.H. & C.S. Odell Opus 327
Scarborough Presbyterian Church, Scarborough, New York

GREAT
16′ Bourdon 70 pipes
8′ Open Diapason 58 pipes
8′ Gamba 58 pipes
8′ Gross Flute 58 pipes
8′ Bourdon (from 16′ Bourdon)
4′ Principal 58 pipes
4′ Harmonic Flute 58 pipes
22⁄3 Twelfth 58 pipes
2′ Fifteenth 58 pipes
13⁄5′ Seventeenth (new) 58 pipes
III Mixture 174 pipes
8′ Trumpet 58 pipes

SWELL – Expressive –
in reconfigured expression chamber
16′ Bourdon 58 pipes
8′ Open Diapason 58 pipes
8′ Stopped Diapason 58 pipes
8′ Salicional 58 pipes
8′ Voix Céleste 58 pipes
4′ Violina 58 pipes
4′ Rohr Flute 58 pipes
2′ Flute 58 pipes
III Cornet 174 pipes
16′ Bassoon 58 pipes
8′ Cornopean 58 pipes
8′ Oboe 58 pipes
4′ Clarion 58 pipes
Tremulant

PEDAL
32′ Resultant (special configuration,
from Open Wood and Bourdon)
16′ Open Wood 30 pipes
16′ Bourdon 54 pipes
8′ Gedeckt (ext 16′ Bourdon)
8′ Violoncello 30 pipes
4′ Flute (ext 16′ Bourdon)
16′ Bassoon (from Swell)

Mixture Compositions
Great
1 to 25 15-19-22
26 to 37 12-15-19
38 to 58 8-12-15

Swell
1 to 25 17-19-22
26 to 37 15-17-19
38 to 58 8-15-17

Couplers
Great to Pedal 8′ (reversible)
Great to Pedal 4′
Swell to Pedal 8′ (reversible)
Swell to Pedal 4′

Great to Great 16′
Great Unison Off
Great to Great 4′

Swell to Great 16′
Swell to Great 8′ (reversible)
Swell to Great 4′

Swell to Swell 16′
Swell Unison Off
Swell to Swell 4′

Pistons
12 generals (duplicated on toe pistons)
6 divisionals per division
4 reversibles (3 coupler, 1 Sforzando)

Accessories
32 levels of capture memory
12-step transposer
Programmable Sforzando
Memory controls in keyslip
Programmable Crescendo
MIDI for record/playback

Organbuilding in the United States and Canada is a thriving art practiced in hundreds of shops throughout the continent. Emerging from decades of stylistic extremes, organbuilders are combining a wealth of knowledge from the past with new technologies to meet contemporary design challenges. North American builders, compelled by a unique spirit of cooperation and openness, are successfully raising the artistic standards of this time-honored craft. (American Institute of Organbuilders, descriptive statement.)

The organ has occupied a prominent place in the musical culture of Canada since the days of the first European settlement, chiefly because of its close connection with church music and the ambitions of many congregations. The first organs, brought from France, were installed in Québec City around 1660. An anecdotal report mentions the acquisition by a Halifax church of a Spanish instrument that had been seized on board a ship in 1765.1 Following a period in which organs continued to be imported from England and France, organbuilding began as early as 1723 and flourished mainly in Québec and Ontario from the mid-19th century onward.2 By the second half of the 19th century, organ building had become a relatively important industry in Eastern Canada, where companies had acquired sufficient expertise to compete in the international market, including the United States.3

The development of organbuilding in Canada proceeded through several phases, beginning with early builders.4  The first known organbuilder was Richard Coates, who arrived in Canada from England in 1817; he supplied mainly barrel organs to several small churches in Ontario. Joseph Casavant, the first Canadian-born builder, installed his first instrument in the Montréal region in 1840; he transmitted his skills to his sons, who later established the company that achieved world-wide recognition. The arrival from the United States of Samuel Russell Warren in 1836 marked the introduction of professional-calibre organbuilding into the country. His family firm had produced about 350 pipe organs by 1869; it was sold in 1896 to D. W. Karn (see below). Other prominent organ builders included Napoléon Déry (active 1874-1889), Eusèbe Brodeur (a successor to Joseph Casavant in 1866), and Louis Mitchell (active 1861-1893) in Québec, and Edward Lye (active 1864-1919) in Ontario.

The years 1880-1950 were marked by unprecedented growth in organbuilding, beginning with the establishment of Casavant Frères in 1879 in Saint-Hyacinthe, Québec. The Canadian Pipe Organ Company/Compagnie d'orgues canadiennes was established in 1910 by some former Casavant staff, also in Saint-Hyacinthe (when the firm closed in 1931 its equipment was acquired by Casavant). Prominent Ontario builders included the firms of Richard S. Williams (founded 1854 in Toronto), Denis W. Karn (commenced 1897 in Woodstock), C. Franklin Legge (founded 1915 in Toronto, joined by William F. Legge 1919, who later established his own company in Woodstock around 1948), and the Woodstock Pipe Organ Builders (an organization of skilled craftsmen in that Ontario town, 1922-1948). Several smaller, independent builders were active for a time in Ontario, the Maritime provinces, and Manitoba (late 1880s). British Columbia, on the other hand, seems to have had no indigenous organbuilders, for instruments were imported from the United States or from England on ships that sailed around Cape Horn; one of the earliest arrived in Victoria from England by this route in 1861.

In the early 1950s some organbuilders, encouraged by younger organists who had played European instruments, as well as the increasing availability of sound recordings of these organs, turned to classical principles of organbuilding to counter what they perceived as the colorless sound palettes of Canadian organs of the 1930s. The return to earlier tonal aesthetics, inspired by the so-called 17th-century "Baroque organ," found expression in the construction of bright-toned, tracker-action instruments. The "new orthodoxy" was enthusiastically assimilated by Casavant Frères and by a number of independent builders in the same region, some of whom had received their training in Europe. Karl Wilhelm, Hellmuth Wolff, André Guilbault and Guy Thérien, Fernand Létourneau, Gabriel Kney, and Gerhard Brunzema were prominent in this movement, and many of them are still in business. Their accomplishments, along with the activities of other known organbuilders of the 1990s, will be described in chronological order, according to their founding dates, in the remainder of this article.5

Casavant Frères, Saint-Hyacinthe, Québec (1879)

Casavant is the oldest continuing name in organbuilding in North America. Joseph Casavant (1807-1874), the father of the founders of the company, began his organbuilding career while still a Latin student at a Québec religious college, where he completed an unfinished organ from France with the help of a classic treatise on organbuilding. By the time he retired in 1866, after 26 years in business in Saint-Hyacinthe, Québec, he had installed organs in 17 churches in Québec and Ontario, but none of them survive. His sons, Joseph-Claver Casavant (1855-1933) and Samuel-Marie Casavant (1850-1929), worked for Eusèbe Brodeur, their father's successor, for a few years. They opened their own factory in Saint-Hyacinthe, Québec, in 1879, following an extended tour of western Europe inspecting organs and visiting workshops; Claver had apprenticed briefly with a Versailles builder before the tour. In the early years the Casavant brothers were conservative in their tonal design, emulating the ensemble sound of the kind they had heard in old-world instruments that they had examined during their European tour. But from the outset the brothers were innovators, beginning with improvements in the electric operation of their organs in the 1890s. As their reputation spread beyond the cities and towns of their province, production increased steadily.

The company experienced difficult times in the 1930s due to economic conditions, much standardization, and repetitive tonal design. Production was curtailed during the years of World War II due to a shortage of materials, and the company manufactured many unit organs during this period. Later, new initiatives were undertaken by several imaginative artistic directors who served with the firm between 1958 and 1965: Lawrence Phelps from Aeolian-Skinner in the U.S.A.; and European-trained Gerhard Brunzema, Karl Wilhelm, and Hellmuth Wolff.

Most present-day Casavant organs exhibit a conventional design that retains both symphonic and modern elements in subtle synthesis. Casavant organs are recognized for their special tonal qualities and the way the individual stops are blended together into a chorus at all dynamic levels. Time-tested actions include tracker, electrically operated slider windchests, and electro-pneumatic (since 1892; tubular-pneumatic was last used in the mid-1940s). The company workshop has eight departments: metalworking, woodworking, mechanism, consoles, painting, racking, voicing, and assembly. Virtually all components are made in the workshop, including all flue and reed pipes (to 32-foot-length), reed shallots, windchests, consoles, keyboards and pedalboards, and casework, although specialized wood carving and gilding are done by outside artisans. A few electrical components, such as blowers, power-supply units, electromagnets, solid-state combination and coupling systems, and hardware, are purchased from world-wide suppliers. All visual designs are coordinated with their intended surroundings; there are no stock designs. Organs are completely assembled for rigorous testing and playing in preparation for on-time delivery.

The company resumed the construction of tracker-action instruments in 1961 after a lapse of about 55 years, producing 216 such organs since that date. By the end of 1998 the total output amounted to 3,775 organs of all sizes, and many of these have received enthusiastic testimonials from renowned recitalists over the years. Although sales were limited mainly to North America until World War II, Casavant organs now have been installed in churches, concert halls, and teaching institutions on five continents. The firm's largest instrument is a five-manual, 129-stop organ with two consoles installed in Broadway Baptist Church, Fort Worth, Texas, in 1996. The great majority of the very large instruments have been installed in locations in the United States; the exception is the four-manual, 75-stop organ in Jack Singer Concert Hall, Calgary Centre for the Performing Arts, in 1987. The company also engages in renovation projects and additions to existing organs.

The key personnel include Pierre Dionne, President and Chief Operating Officer (from 1978), formerly Dean of Administration at the Business School of the University of Montréal; Stanley Scheer, Vice-President (1984), formerly Professor of Music and Head of the Department of Fine Arts at Pfeiffer University, Misenheimer, North Carolina, holds a Master of Music degree in organ performance from Westminster Choir College, Princeton, New Jersey; Jean-Louis Coignet, Tonal Director (1981), a professionally trained physiologist with a doctorate from the Sorbonne, contributor to music journals, the most knowledgeable authority on the work of Cavaillé-Coll today, was formerly organ expert for the City of Paris; Jacquelin Rochette, Associate Tonal Director (1984), formerly Music Director of Chalmers-Wesley United Church, Québec City, holds a Master's degree in organ performance from Laval University, performs regularly on CBC radio, and has recorded works by several French composers for organ; Denis Blain, Technical Director (1986), with many years of practical experience in virtually all aspects of organbuilding, is in charge of research and development; Pierre Drouin, Chief Engineer, holds a Bachelor of Architecture degree from Laval University, introduced computer-assisted drafting, and supervises the design and layout of each organ. In 1998 the company had 85 full-time employees, many with more than 30 years of service with the company. All levels of management and production personnel function as a team.

Keates-Geissler Pipe Organs, Guelph, Ontario (1945)

The company was established in 1945 in London, Ontario, by Bert Keates (he came from England in his infancy) and relocated to Lucan, Ontario, in 1950. When it was incorporated in 1951 the assets of the Woodstock Pipe Organ Builders (formerly Karn-Warren) were purchased. The company moved to Acton, Ontario, in 1961, a more central location in the province. In 1969 the growing firm took over the business of the J. C. Hallman Company, a manufacturer of electronic instruments and pipe organs, when it discontinued making pipe organs (but not parts for them). For several years some organs were manufactured under the name of Keates-Hallman Pipe Organs.6 The company moved to Guelph, Ontario, in 1994.

Dieter Geissler was born in Dittelsdorf, Saxony, Germany, where he began his trade as a cabinetmaker. At the age of 14 he commenced his apprenticeship with Schuster & Sohn, Zitau, where he remained from 1946 to 1950. In 1951 he moved to Lübeck, West Germany, where he worked as a voicer with E. Kemper & Sohn for five years. In 1956 he moved to Canada to join Keates's staff. When Keates retired at the end of 1971 Dieter Geissler became president of the firm, which he purchased in 1972, and adopted the present company name in 1982. His son, Jens Geissler, joined the company in 1978.

Keates-Geissler organs are offered in all types of action and are custom built to any required size. Altogether, 147 new organs7 have been installed at locations in Canada, the United States (about 15), and Barbados, West Indies. The output includes a number of four- and five-manual instruments; the largest is a five-manual, 231-stop organ, installed in the First Baptist Church, Jackson, Mississippi, in 1992 (a compilation of its original 1939 E. M. Skinner instrument, a 1929 five-manual Casavant organ removed by Keates-Geissler in 1986 from the Royal York Hotel, Toronto, and some additional structures by the company). The firm has undertaken a substantial number of renovation, rebuilding, and reinstallation projects over the years, about 1,500 altogether, about 75 of these in the United States.

All wooden pipes are made in the factory, but metal pipes are made by Giesecke or Laukhuff in Germany to the company's scaling specifications; preliminary voicing is done in the factory before final voicing on-site. The windchests of electro-pneumatic instruments feature Pitman-chest action that includes some unique features to overcome the effects of extremes in temperature and humidity; the company is the only such manufacturer in Ontario and one of a few in Canada. Expandable electronic switching systems are designed and made in the factory from readily available components to facilitate replacement. Solid-state switching and multiple-memory combination actions are also manufactured. Console shells are handcrafted from solid wood in the factory; tracker touch is an available option. Keyboards are custom made to the company's specifications by Laukhuff, Germany, and blowers are acquired mainly from the same company. The company had four full-time employees in 1998; other part-time workers are hired as needed.  

Guilbault-Thérien, Saint-Hyacinthe, Québec (1946)

This company originated with the Providence Organ Company, established in Saint-Hyacinthe in 1946. The partners, André Guilbault, whose father Maurice Guilbault had worked for Casavant, and Guy Thérien, a voicer from Casavant, joined forces in 1968 when the elder Guilbault retired. The present company name was adopted in 1979. When André Guilbault retired in 1992, Alain Guilbault (no relation) acquired an interest in the company.

At the outset the company manufactured electro-pneumatic instruments, but built its first mechanical-action instrument (Opus #1 in a new series), a two-manual, 7-stop organ, in 1970, immediately followed by several small one- and two-manual instruments. From 1974 onward the typical instruments were medium-size, two-manual organs. Larger instruments of three or four manuals began to appear with greater frequency after 1983, the largest being a four-manual, 45-stop organ installed in Grace Church, White Plains, New York, in 1989, the only installation in the United States to that time. While the tonal layout of the organs is mainly inspired by European sources, mainly French, the swell divisions of the larger instruments are sufficiently versatile to handle symphonic literature.

The output of new organs was about 55 to 1998, mainly in Québec and Ontario. The company's work has also involved the restoration and reconstruction of a similar number of Québec organs, mainly by Casavant, but including some of historical significance that are over a hundred years old by such early builders as Napoléon Déry and Louis Mitchell. 

Several compact discs featuring performances by Québec organists on instruments manufactured by the company, or on reconstructed historical Casavant instruments, have been released in the past decade.8

Principal Pipe Organ Company, Woodstock, Ontario (1961)

The company was established by Chris Houthuyzen in Woodstock, Ontario, a town with a continuing tradition of organbuilding. The founder served his apprenticeship and received further training in The Netherlands before coming to Canada. Small to medium-sized instruments, employing electro-pneumatic action, are the company's specialty, with a contemporary emphasis on the guiding principles of Dutch organbuilding. A total of 119 installations have been completed over the years; the largest was a four-manual, 58-rank instrument. Wooden pipes are made in the shop, but most metal pipes come from suppliers in the United States; their scaling is dictated by the acoustics and intended use of the organ. Chests, reservoirs, ducting, consoles, and casework are manufactured on the premises. Much of the company's work involves rebuilding and maintaining organs, as well as the installation and servicing of church bells, including cast and electronic carillons on behalf of the Verdin Company, Cincinnati, Ohio. The company had three employees in 1998.

Gabriel Kney, London, Ontario (1962-1996)

Gabriel Kney was born in Speyer, Germany; his father was a master cabinetmaker and amateur bassoonist, and his mother was a singer. He served his apprenticeship in organbuilding with Paul Sattel in Speyer (1945-1951), where he assisted in the restoration of historic, sometimes war-damaged, instruments, along with new organ construction. Since the era was a time of transition from the "Romantic" style of organbuilding to the concepts of Orgelbewegung, this trend provided him with the opportunity to learn about and participate in the building of organs of both concepts. Concurrently he was a student of organ literature, liturgical music, harmony, and improvisation at The Institute of Church Music in the same city.

He emigrated to Canada in 1951 and joined the Keates Organ Company in Lucan, Ontario, as an organbuilder and voicer. In 1955 he was co-founder, with John Bright, of the Kney and Bright Organ Company in London, Ontario, with the intention of specializing in tracker instruments. The timing was premature, for only a few musicians and teaching institutions found such instruments of interest; with the exception of two teaching organs of tracker design supplied to a college in the United States, most of the early organs were requested to have electric key action. In 1962 Gabriel Kney established his own company in London, Ontario, where, with enlarged facilities and a staff of six to eight, he specialized in mechanical-action instruments. Organs from the period between 1962 and 1966 were designed in the historic manner of Werkprinzip, with organ pipes enclosed in a free-standing casework and separated into tonal sections. The tonal design of smaller instruments followed 18th-century North European practices, with some tuned in unequal temperaments of the period.

Altogether, his shops produced 128 organs since 1955; the largest in Canada being the four-manual, 71-stop, tracker-action instrument with two consoles in Roy Thomson Hall, Toronto. Since the early 1970s almost three-quarters of the installations were in locations in the United States, several of these in large universities. Occasionally maintenance and historic instrument restoration projects were undertaken.

Wooden pipes were made in the shop, with the exception of very large pipes made to specifications by suppliers in the United States, England, or Germany. Metal pipes also were made to order by independent pipemakers in Germany or Holland. Some console components, such as keyboards, were obtained from suppliers in the United States, England, or Germany. Electric switching devices came from the United States in earlier years, later from England. Blowers were imported from Laukhuff in Germany, Meidinger in Switzerland, or White in the United States. All casework and chest construction was done in the shop.

In 1996 Gabriel Kney retired from active organbuilding and closed his company. Since then he has acted as a consultant to churches seeking advice on organ purchase, restoration, and tonal redesign, and sometimes to other organbuilders.

Karl Wilhelm, Mont Saint-Hilaire, Québec (1966)

Karl Wilhelm was born in Lichtenthal, Rumania, and grew up in Weikersheim, Germany. At the age of 16 he entered apprenticeship with A. Laukhuff, Weikersheim (1952-1956), followed by working experience with W. E. Renkewitz, Nehren/Tübingen (1956-1957), and Metzler & Söhne, Dietikon, Switzerland (1957-1960). After moving to Canada, in 1960 he joined Casavant Frères, where he established the department and trained several employees for the production of modern mechanical organs; while there he was responsible for the design and manufacture of 26 organs. In 1966 he established his own firm, first in Saint-Hyacinthe, then moved to new facilities in Mont Saint-Hilaire, near Montréal, Québec, in 1974. For a while he was assisted by Hellmuth Wolff, now an independent builder (see below).

Karl Wilhelm specializes in building mechanical organs of all sizes, 147 to date, of which 69 are located in the United States and two in Seoul, Korea. Of the total output, 43 are one-manual instruments, 93 are two-manual instruments of medium size, and 11 are three-manual instruments--the largest is a 50-stop instrument in St. Andrew's Presbyterian Church, Toronto, installed in 1983. Two have detached consoles, and four have combination actions with electric stop-action; all instruments have mechanical key action. The design and layout of instruments adhere to the principles of the classical tradition of German and French organbuilding. Three-manual instruments feature a large swell division, suitable for the performance of Anglican Church music and the Romantic repertoire.

All wooden pipes are made on the premises, along with almost one-half of the metal pipes that are handmade of a tin-lead alloy; other metal pipes are imported from Germany. Scaling and voicing are done in the classical open-toe manner for natural speech and mellow blend. Windchests and bellows, consoles and action, and cases are manufactured in a 9,000 sq. ft. workshop. Organs may have cases of contemporary design, or perhaps are more ornate with moldings and hand-carved pipe shades that are compatible with the architecture of the location. Blowers are acquired from Laukhuff, Germany; miscellaneous parts come from other suppliers. The firm does not engage in rebuilding or renovation but services and tunes its own instruments throughout North America. In 1998 the firm had five employees, all trained by Karl Wilhelm.

Wolff & Associés, Laval, Québec (1968)

Hellmuth Wolff was born in Zurich, Switzerland. While a teenager he apprenticed with Metzler & Söhne, Dietikon, Switzerland (1953-1957); in his spare time he built his first organ, a four-stop positiv instrument. He received additional training with G. A. C. de Graff, Amsterdam (1958-1960) and with Rieger Orgelbau, Schwarzach, Austria (1960-1962). In the United States (1962-1963) he worked with Otto Hofmann, in Austin, Texas, and Charles Fisk, in Gloucester, Massachusetts. After moving to Canada he worked with Casavant Frères (1963-1965) in its newly established tracker-action department, and then with Karl Wilhelm (1966-1968), with whom he had worked at Casavant. In the interval 1965-1966 he returned briefly to Europe to work as a designer and voicer with Manufacture d'orgues Genève, in Geneva. Besides playing the piano and singing in choirs wherever he went, he completed his musical training by taking organ lessons with Win Dalm in Amsterdam and later with Bernard Lagacé in Montréal.

In 1968 he opened his own business in Laval, Québec, with one employee; his present associate, James Louder, started his apprenticeship with Hellmuth Wolff in 1974, after training in classical guitar and English. The first large project undertaken in that year was the construction of a three-manual, 26-stop instrument at the Church of St. John the Evangelist, New York City; this was one of the city's first modern tracker-action organs and it incorporated features not yet seen in North America. In 1977 the company moved to a new shop; the firm became incorporated in 1981, and James Louder became a partner in 1988.

Hellmuth Wolff has been part of the Organ Reform in North America since the movement came to this continent in the early 1960s. He specializes in mechanical-action instruments, large and small, whose design is inspired by French or German classical traditions, although other styles are represented that are designed to accommodate a wide range of organ literature. A total of 42 organs have been manufactured; about one-half of these were installed in locations in the United States. While a few small residence or practice instruments have been built, the majority are two-manual organs, in addition to eight three-manual organs, and one four-manual, 50-stop/70-rank instrument installed in Christ Church Cathedral, Indianapolis, Indiana, in 1989.9 Other related activities include rebuilding, restoration, and maintenance work, chiefly in the Montréal area.

Wooden pipes are made on the premises, while metal pipes are acquired from several pipemakers in Canada, U.S.A., and Europe; some reeds are made there, also. Windchests, consoles, and cases are also manufactured on site. Blowers are acquired from Meidinger and Laukhuff in Germany. Several installations feature both mechanical stop-action and capture systems; the first was built in 1977 for the Eighth Church of Christ, Scientist, in New York City; it was probably the first such system in North America. Both sequencers and traditional multilevel capture systems are used. There were eight employees in 1998.

Hellmuth Wolff, along with his associate, James Louder, have contributed to symposiums and written publications on organs and organbuilding.10 Fourteen compact discs, featuring performances by Canadian and American artists on Wolff instruments, have been released, and three others are in preparation.11

Brunzema Organs, Fergus, Ontario (1979-1992)

Gerhard Brunzema was born in Emden, Germany, and grew up in Menden on the Ruhr river, a northern part of the country where there was an abundance of historic organs. After World War II he apprenticed with Paul Ott in Göttingen and worked with him as a journeyman organbuilder (1948-1952). He received extensive technical training, including acoustics, at the Brunswick State Institute for Physics and Technology (1953-1954), and received a Master's degree in organbuilding in 1955. In 1953 he joined the prominent European organbuilder Jürgen Ahrend in the construction and restoration of organs, some in Holland and Germany of great historical significance; this association continued for 18 years. After emigrating to Canada he joined Casavant Frères in 1972 and served as artistic director until 1979; during that time he was responsible for the design of several notable organs in Canada, the United States, Japan, and Australia, along with the restoration of a number of historic Casavant instruments in Ontario and Québec. His experience at Casavant gave him the opportunity to work with very large organs, an experience that was lacking in Germany.

In 1979 he established his own business in Fergus, Ontario. Throughout his career he specialized mainly in small, one-manual, four-stop, continuo organs (25 in all); most of his nine two-manual instruments--the largest was 25 stops--were made between 1985 and 1987. In 1990 he was joined by his son, Friedrich, who had completed his apprenticeship in Europe. Until the time of his death in 1992, Gerhard Brunzema's total output amounted to 41 instruments; of these, 20 were installed in Canadian locations (mainly in eastern provinces), 17 in the United States, one in the Philippines, one in South Korea, and two in European countries. The tonal design of his instruments was strongly influenced by Schnitger organs that he had studied and restored while in Europe. He believed that basic organ design cannot be learned through restoration work, because such instruments were conceived by others; nevertheless, in restorations the intentions of the original builders should be respected. As for new instruments, his philosophy was that "An organbuilder should choose a style and stay with it, so that he not only continues to develop his own skills, but also continues to help improve the skills of the people working for him. . . . Become a master of one thing, get over the initial difficulties very quickly, and then polish your knowledge, the details of which will finally add up to a very good result."12

Koppejan Pipe Organs, Chilliwack, British Columbia (1979)

Adrian Koppejan was born in Veenendaal, Holland, and apprenticed with his father, who was an organbuilder there. He worked with Friedrich Weigle in Echterdingen by Stuttgart, Germany (1963-1966), with Pels & Van Leeuwen in Alkmaar, Holland (1968-1972) as shop foreman of the mechanical organ department, and with his father's company, Koppejan Pipe Organs, in Ederveen, Holland (1968-1972). He moved to Canada in 1974 and established his own company five years later.

Adrian Koppejan strives for a clear, warm, but not loud sound in his instruments, a preference inspired by classical organs of North Germany. This sound palette is reflected in the instruments in which he specializes: small and medium-size tracker instruments; he has built five electromechanical organs, as well. His output to date consists of 19 organs; these have been installed in churches and private residences in British Columbia, Alberta, and Washington state. His largest organ is a three-manual, 31-stop, electromechanical instrument, with a MIDI system, installed in the Good Shepherd Church, White Rock, B.C., in 1995. An instrument of similar size was constructed in 1998. Rebuilding, restoration, maintenance, and tuning are also part of regular activities.

Wooden pipes are mostly acquired from Laukhuff, Germany; metal pipes come from Stinkens in Holland and Laukhuff in Germany. Keyboards are made in Germany by Laukhuff or Heuss. Winding mechanisms, consoles, solid oak cabinets, and casework are manufactured in the shop. Blowers are supplied by Laukhuff, and electrical control systems come from Peterson in the U.S.A. There were two part-time employees in 1998 as Adrian Koppejan reduced the scope of his operations in anticipation of retirement.

Orgues Létourneau,  Saint-Hyacinthe, Québec (1979)

Fernand Létourneau was born in Saint-Hyacinthe, Québec, where he worked for while as a carpenter before entering employment with Casavant Frères in 1965; there he apprenticed with his uncle, Jean-Paul Létourneau, who was head reed voicer. He remained with the company for 14 years, where he was head voicer from 1975 to 1978, when he decided to set up his own independent company. First, with the help of a Canada Council grant, he embarked on an organ tour of Europe to study the voicing of old masters. Upon his return to Canada in 1978 he began building organs in Sainte-Rosalie, Québec, and became incorporated in 1979. His first organ, a two-manual, 6-stop instrument, was started in the basement of the family house and then displayed in the shop of a cabinetmaker; it was later acquired by the Conservatoire de Musique du Québec, Hull, where dozens of students have learned to play the organ on this small instrument. In 1984 he moved back to Saint-Hyacinthe, where three other organbuilders were already established. The factory's first building was formerly a municipal water-filter plant; the partially underground space provided a room 35 feet in height, ideal for erecting organs. A second industrial building was acquired recently to supplement the original premises.

A total of 55 organs of various sizes have been built to 1998; 13 others are in progress. The great majority have mechanical action, utilizing classical principles used in European instruments, and with the flexibility provided by ranks inspired by Dom Bédos, Schnitger, and Cavaillé-Coll. The largest will be a four-manual, 101-stop, mechanical-action instrument intended for the Francis Winspear Centre, Edmonton, Alberta. International distribution has been common from the outset, beginning with three early instruments that were installed in Australian locations in the early 1980s (the builder had become known on account of his activities as a voicer of Casavant instruments in that country). Others have been placed in New Zealand, Austria, England (Pembroke College, Oxford, 1995; an instrument is under construction for the Tower of London for completion in late 1999), the United States (over one-third of the total production), and Canada (chiefly eastern provinces, a few in the west). The company now has permanent representatives in the United States, England, and New Zealand. Fernand Létourneau prefers to build instruments of eclectic tonal design that are suitable for the performance of a wide range of organ literature. Historic restorations have also been undertaken.

All organ components, with the exception of electronics, are made in the factory, including wooden and metal pipes to 32-foot length, keyboards, consoles, and casework. Blowers are acquired from Laukhuff, Germany. Middle-size organs are equipped with electronic sequencers, card readers, and similar devices. The company is constantly engaged in rebuilding and restoring instruments of different vintages to original condition, about 50 to date, several of which have been designated as historical or heritage instruments. In 1998 there were 45 full-time staff in the Létourneau "family," of which a number are related to one another as father-son/daughter, uncle, brother, cousin, and husband-wife.