J.H. & C.S. Odell Opus 645
United Methodist Church of Westport and Weston,
Westport, Connecticut
From the builder
I first looked over the 1968 Angell pipe organ at the United Methodist Church of Westport and Weston in the winter of 2005, having been recommended to the church by our friend K. Bryan Kirk. What we found in Westport was an organ with many pipes that were well made, but in some cases unusually constructed and, by our standards, only roughly voiced. The flue pipes were made mostly with a high content of tin. We suspect Tim Koelewijn was the original pipemaker. Just about everything else in the organ had been made by domestic and foreign supply houses. Overall, quality varied widely. Some things were very neatly done.
Though by our standards not altogether under-scaled, the organ did suffer in just about every other way from the prevailing trends of the era when it was built. Wind pressures were low: less than two inches in the Great and three in the Swell. Looking at the original stoplist, we noted that none of the choruses in the organ were complete, though the organ did boast two Célestes and a triple-overblowing Zauberflöte. The reed complement for the organ consisted of a double-blocked French style 8’ Trompette (extended to 16’ in the Pedal) and a 4’ Rohr Shalmei.
The windchest mechanism was a problematic plunger-type solenoid system that had been giving trouble for years. The console was a veneered plywood supply house unit already years beyond its life expectancy. The open contact switching system was dispersed throughout the organ; some of its components had already failed. The wind supply for the entire Great division was provided by a single 18≤ by 24≤ reservoir whose internal volume was largely dedicated to its curtain valve.
After an initial tuning of the organ, the church’s new music director and organist, Todd Simmons, pressed me as to what could be done to make the organ better. I pointed out that the organ had mechanical and tonal issues, to be sure, but there was something to work with here, some raw material, which with proper attention could be the basis for a good pipe organ. In my wife Holly’s words, the existing pipework possessed “unrealized potential.”
Weeks later we met with the trustees to present our findings, expecting that at some point in the future funds could be raised to finance the organ project. One can imagine my surprise when Mr. Simmons called me a few weeks later to say that a single anonymous donor had stepped forward. How soon could we start? Thus we found ourselves sweating in the summer heat on a stretch of days the following July, packing and removing the pipes that would become the basis for our Opus 645.
In the design process we developed a new specification with input from K. Bryan Kirk. We instinctively sought first to meet the essential requirements of a liturgical instrument, something we believe to be utterly crucial, especially in the case of smaller pipe organs. Given the limited space for the organ, we felt a two-manual scheme with few frills would be best. We resisted a request for digital augmentation, instead focusing on a design that would be pipe only.
Certain early decisions seemed obvious. Given the dry acoustic of the church, the baseline scale of the Great chorus needed to be increased. This chorus was also completed with the addition of appropriately scaled new pipework from 22⁄3’ pitch upward. The cutup schedule of the existing Great capped flute was raised, arched, and the stop entirely revoiced. A new independent 4’ Harmonic Flute (based on the unique and very successful scale found in our historic Opus 178 at St. Charles Borromeo in Brooklyn) was constructed and voiced. Over the course of the project nearly every zinc pipe in the organ made its way through our pipe shop: frozen metal caps were freed, tuning inserts and toes replaced, seams and scrolls repaired. Being left in a raw state, many of the zinc pipes had an unsightly powdery white oxidation. We removed this, and gave all zinc basses a sealing coat of varnish to protect them.
The wind pressure of all manual divisions was raised to a more moderate four inches. Holly, then pregnant with our son Caleb, did her usual superb job of revoicing all the other existing and new flue pipework, managing to do so before reaching her final trimester. During this past winter we joked more than once: which would be given birth first, our son Caleb or the organ for Westport?
Where, before, the Great division of the organ had seven ranks, it had now eleven. To provide for this expanded division adequately, we built a new, larger reservoir. The rest of the organ’s wind system was rebuilt and reengineered as the new design required.
In dealing with the Swell division, again certain decisions seemed obvious. The 4’ Rohr Shalmei, only marginally useful, was replaced with an 8’ Oboe, expertly voiced by Sam Hughes. Proceeding as she did in the Great, Holly revoiced all of the existing Swell flues and voiced the new pipework for the Swell flute chorus, which was completed to 13⁄5’ pitch. The existing Trompette was kept, though carefully cleaned up and regulated in a cooperative effort between Sam and Holly.
In our recently expanded East Hampton shop I concentrated on the construction of the console, while our shop foreman John Williams constructed new windchests whose design was first developed for our organ at St. Ann’s in Bridgehampton. The unusually short feet of the 8’ old flute basses made for some interesting pipesetting. New offset chests were provided for everything save the original Pedal Subbass, a mammoth mahogany affair that only needed rebuilding.
The new console was based on our current terrace-jamb design with several embellishments. Improvements on the existing design include a slightly deeper cabinet with an added horizontal stile, raised panel work, additional applied moldings, hand-carved brackets, a two-piece knee panel and solid walnut music desk, the latter being picture-framed with the same quarter-sawn white oak used for the carcass and façade.
The console features an integrated solid-state capture and control system with fully programmable features, MIDI interface, and our standard complement of rear-fulcrum keyboards with basswood levers. The oblique drawknob heads are a reproduction of our 19th-century design. Respected organists who have played it have described our console at Westport as “elegant and comfortable.”
My design of the façade was in part born of necessity. Since both the manual and pedal principal stops were being rescaled, new bass pipes would be required. We naturally needed to make the most of the existing chamber space, and one of the simplest ways to do that was by moving the basses of these stops out into a façade.
Every pipe in the façade is functional. The bass notes of the Great and Pedal principals are polished aluminum, made to our specifications by Matters, Inc. of Hermosa, South Dakota. The pipes are arranged in three towers and two flats and the overall height of the case tops out at 15 feet, mounted roughly 10 feet above the sanctuary floor. The style of the casework is deliberately simple, so as to be in harmony with the appointments of the church sanctuary.
The façade performs a very important function in giving one a visual focal point. It declares the organ present, and urges one to consider it rather than wonder from where behind the grille cloth the organ might be. Its cruciform arrangement also reflects elements of sacred numerology: three towers with three pipes each for the Trinity, ten pipes located within the inner flats for the Commandments.
The sanctuary space in Westport could be described as a postwar-modernist take on the “Akron Plan,” less the adjoining Fellowship Hall. Four sets of pews radiate from the altar and pulpit up front, with organ and choir off to the left. The space over the altar is open with a ceiling height of approximately 35 feet. This intersects with a lower A-frame suspended transversely over the pews. From there the ceiling slopes downward to the rear of the pews to meet a northeasterly facing wall that is mostly glass. The floor is a simple concrete aggregate. Thankfully, carpet was absent. More simply described, it is a space with a great deal of cubic volume, but not overly reverberant.
Throughout the process we gave a great deal of thought to what levels of power would be appropriate for the various tonal resources of the organ. Our concerns about sufficient tonal egress from the chambers were put to rest when we experienced how well the organ spoke into the room. In the tonal finishing process we were pleased to discover how our scaling and voicing decisions suited the space. With a well-balanced variety of 8’ tone available, the organ easily leads congregational singing in a variety of settings.
Overall, we are very happy with what we have achieved in Westport. I would be remiss not to mention others who have contributed to this project: my wife and business partner Holly Odell was responsible for revoicing all existing pipework and voicing of new pipework. John Williams built nearly all the windchests and was responsible for all pipesetting. John and I collaborated on the wind reservoirs and organ case elements. In addition to overall mechanical design and layout, I milled, built and finished the console and casework as well as handling most other finishing duties. Working out of our pipe shop, Stewart Skates handled all pipe repairs. Luc Ladurantaye of Lac Saguay, Quebec, built the new metal pipes to our specifications. Gordon Auchincloss assisted in the wiring and final assembly of the console, and Thomas White assisted in windchest construction and wiring. John Williams, Thomas White, and myself handled the installation. Tonal finishing duties were divided between Holly and myself, with occasional assistance from Richard Hamar and Fred Heffner.
—Edward Odell
From the music director
In my third year as choir director and first year as organist of the United Methodist Church of Westport and Weston, I was introduced to Edward Odell by K. Bryan Kirk, as we were in search of someone local to assume the maintenance of our Angell pipe organ. While I was not dissatisfied with the firm maintaining our organ at that time, I knew it was only a matter of time before a major overhaul was needed, and no one had ever made a complete inspection and report on our instrument. Given the current condition of our organ, I felt comforted in knowing someone local could resuscitate it at a moment’s notice.
After a thorough tuning and evaluation of the organ, I was encouraged by Mr. Odell’s report that although there were serious electrical and tonal issues present, the pipes themselves were well made and could be repaired and voiced (apparently for the first time ever) if we had the means to fund an organ project. Having just completed a fund-raising campaign for a new grand piano, our church did not have extra money to start an organ building fund-raiser, and we felt uncomfortable asking the congregation to dig into their wallets again so soon. This was discouraging as we knew that time was close at hand; in recent years our organ had become increasingly undependable.
Not long after we began exploring these issues, it happened one Sunday morning that the entire organ pedalboard suddenly made itself unusable. Having little alternative, I decided to play that morning’s service on the piano. This coming just a few weeks after Mr. Odell’s presentation to our trustees, there was (understandably) a certain degree of panic, since we were totally unprepared financially to fund an organ project this soon. Even though our organ was one of the longest surviving Angell pipe organs in the area, we had hoped (and expected) it to last longer. It was more and more apparent that something had to be done soon. Before we even had a chance to strategize, I received a call the next day from the pastor informing me that a donor wishing to remain anonymous had left a very large check on his desk with the intention of funding the organ project.
As has been elsewhere stated, our previous instrument suffered from a lack of tonal finishing and the pipes themselves had never been voiced properly. The pipes being of relatively small scale, we were used to a thin, shallow sound that did not possess enough power to adequately fill our worship space, even when I registered full organ. At the start of the project, I had doubts as to whether any new organ would be strong enough, given the room’s difficult acoustics and the location of the organ chambers. Mr. Odell assured us that once the new organ was installed, we would be amazed at the difference.
One of the most impressive enhancements with the new organ, aside from the exquisite façade, is the quality of sound as well as the power behind it. We now have an instrument that adequately leads our congregation in singing, as well as providing full, but subtle, accompaniment for the choir anthems. I can honestly say that at every step of the way, Mr. Odell and his firm have not only met but exceeded my expectations with our new organ and have gone above and beyond the call of duty to deliver an instrument that is even better than the original proposal stated.
It is a testament to his excellent work that not only do the trained musicians in the congregation appreciate this new pipe organ, even the untrained listeners have noticed a huge improvement over the previous instrument. One member (who at one time happened to be unsupportive of the project) admits that now she could not imagine our service without a pipe organ. The church is well pleased, as am I, and we celebrate at every Sunday service this work of art courtesy of the firm of J.H. & C.S. Odell.
—Todd Simmons, organist and music director, United Methodist Church of Westport and Weston
From the consultant
When I began teaching in 1988 at a music school in Westport, Connecticut, I was naturally curious about local pipe organs. Over the years, I became more familiar with the organ at a nearby church: the United Methodist Church of Westport and Weston. The instrument was in poor mechanical condition: it exhibited a failing combination action, frequent ciphers, tuning instability and other frustrations, even though periodic maintenance was given. Being a product of its time, it was very thin in sound, had little bass response (as did the room) and few solo colors. Most importantly, there was no sense of real ensemble, even when the tutti was drawn. The instrument was also limited in its dynamic range for choral accompaniment and congregational singing, and was weak when trying to blend with other instruments. Overall, the organ did not make a strong impact.
A few years later a new organist and choir director was hired, Todd Simmons, one of my teaching colleagues from the music school. As the organ continued to deteriorate, he and the church became even more disappointed with the organ’s unreliability and marginal tonal resources. Knowing I had done other consulting work, Todd asked me to work with him and the church regarding the organ. Realizing the inherent problems, both musical and mechanical, we began an in-depth study of what could be done to either rebuild or replace the organ with something that would not only offer more tonal possibilities but also fill the room and excite the strong congregational singing potential we knew was there.
As we talked, it was apparent that virtually a new organ would be the best option, although much of the existing pipework could be retained if it were rescaled, revoiced and placed on a new, reliable chassis. The organ needed to be reliable and have a wider dynamic range, more tonal colors and a strong sense of presence in the room. It had to strongly lead and accompany congregational singing and sensitively render choral, solo and instrumental accompaniment.
From the outset, one of my pervading concerns was the church’s acoustic, which, while fine for chamber music, was a bit dry for organ and choral music and congregational singing. Having noted the difference in the acoustic when the room was more fully occupied, I knew the challenge of filling the room efficiently would be a mandate for the builder.
Our task began to take shape. Meetings were held and candidate builders were vetted. As work continued, a stop-list began to emerge, while we kept in mind budget and space limitations. One of my thoughts was to ask for a façade, as the previous organ had nothing visible but for a console in a lowered pit in the choir area. I reasoned that a façade would reinforce the impression that the church was getting something new, better and different. We agreed from the beginning that the organ should remain an all-pipe instrument.
After naming a few candidates, one firm was clearly the most interested, experienced and willing to work with us and on this organ. Having known the Odells and their fine lineage of historic instruments as well as their excellent work on new organs and various projects over many years, I was happy to welcome their presence.
The church had Edward and Holly Odell give the organ a full tuning and submit a proposal for either rebuilding or a new organ. As the Odells looked through the organ, they determined that a new console, chassis and electrical system would be required, and that it would be possible to rebuild one small windchest, but otherwise new windchests would be required throughout. By adding a façade for visual interest, some new pipework and retaining about half the existing pipework (though carefully rescaled and revoiced), the organ could take on a new character that would be far more flexible and of greater quality than its predecessor. This concept, coupled with their thorough proposal, helped to land them the contract.
As the new organ design was developed, the specification was refined. Among the ideas we discussed was the clever suggestion to borrow the Great 4’ Octave as an 8’ Second Principal stop on the Great, creating a secondary 8’ Principal for smaller combinations. The stop could also be used to fill out foundation tone when needed. As we continued to explore various tonal issues, it was noted that the old organ had no soft reed color or solo flute color. Among other things, Odell suggested adding an 8’ Oboe and building a new Harmonic Flute, patterned after historic Odell examples, but carefully adapted for the flute scales at Westport.
My early recommendations had included new 22⁄3’ and 2’ principal stops to replace the existing flute-scaled 2’ in the Great. The Odells suggested going further to install a new Mixture to create a full Principal chorus, giving the organ a sense of ensemble, a true plenum, something it never had.
Having listened to the result, I can state these stops create a truly full-sounding principal chorus, finally integrating the instrument into the room. The organ as conceived by the Odells has made a huge difference for hymn and repertoire playing and can now “ring the room” more effectively.
The Great also contains the revoiced 8’ Bourdon, now sounding more like a continuo stop, suitable in choral music or to accompany the Swell’s cornet decomposée. The Gemshorn and its Celeste were retained for flexibility in accompanying and providing more soft colors.
The Swell received “the Odell treatment,” in that all the pipework was revoiced. The flues, strings and mutations were all transformed by voicer Holly Odell, and the reeds were reworked to make a dramatic difference. The strings and 8’ Rohrflute now have more presence and can fully support the choir, as well as contribute to the ensemble. The Swell cornet decomposée is now nicely balanced, and the flutes have a more piquant character.
The new 8’ Oboe offers a nice color for softer choral accompaniment and foundation combinations, as well as providing a new solo stop. The existing 8’ Trompette, originally extended to 16’ for the Pedal, was also cleaned, revoiced and regulated into a stop that now serves a dual-purpose chorus/solo reed. The 16’ octave, now reconditioned, adds more gravitas to the Pedal and the full ensemble.
The full ensemble now fills the church worship space with a richer, warmer and well-blended tone. The softer sounds are more usable and possess a wider dynamic range, so the possibilities for choral, vocal and instrumental accompaniment are greatly enhanced.
As a concerned observer, I paid close attention to the project throughout the building process. The Odells always welcomed my inquiries and kept all parties informed with frequent photographs from their shop. Once the installation commenced, it was exciting to see how beautifully designed and well made all components of the organ were, both inside and out. During the tonal finishing, it was gratifying to witness the attention to detail in balancing each stop and the various ensembles. Further, it was refreshing to hear from the builder that materials and workmanship were never an issue; they simply insisted that in every aspect things be done thoroughly, with the highest level of attention to detail.
The organ is now in regular use and a series of dedication concerts have been planned. My thanks go to Edward and Holly Odell, their associates, to Todd Simmons and the United Methodist Church of Westport and Weston, Connecticut, and the donor for having me work with them in a collaborative effort to complete this important project to enrich the worship and outreach of this vibrant congregation.
—K. Bryan Kirk, advisor/consultant
J.H. & C.S. Odell Opus 645
United Methodist Church of Westport and Weston, Westport, Connecticut
Great (Wind pressure 4")
8’ Principal CC–AA en façade, otherwise 70% tin, 61 pipes
8’ Second Principal 1–12 from Principal 8’, 13–49 from Octave 4’
8’ Bourdon 70% tin, arched cutup, 61 pipes
8’ Harmonic Flute 1–12 from Bourdon 8’, 13–61 from Harmonic Flute 4’
8’ Gemshorn 70% tin, 2/3 taper, 61 pipes
8’ Gemshorn Céleste 70% tin, 2/3 taper, 49 pipes
4’ Octave 70% tin, 61 pipes
4’ Harmonic Flute 55% spotted metal, special Odell scale, harmonic at
middle C, 61 pipes
22⁄3’ Quint 55% spotted metal, 61 pipes
2’ Super Octave 55% spotted metal, 61 pipes
III Mixture 55% spotted metal, 19-22-26, 183 pipes
Chimes. 25 tubes
Swell (Expressive, in existing chamber, wind pressure 4")
16’ Rohr Gedeckt wood, 13–61 from Rohr Flute 8’, 12 pipes
8’ Rohr Flute 70% tin, chimneyed, 61 pipes
8’ Gamba 70% tin, bearded, 61 pipes
8’ Gamba Céleste 70% tin, bearded, 49 pipes
4’ Spitz Principal 70% tin, 2/3 taper, 61 pipes
4’ Flute 55% spotted metal, 2/3 taper, 61 pipes
22⁄3’ Nazard 70% tin, capped and chimneyed to middle C, 61 pipes
2’ Block Flute 70% tin, 61 pipes
13⁄5’ Tierce 55% spotted metal, 2/3 taper, 61 pipes
8’ Trompette double blocked, French shallots, 56 reeds, 61 pipes
8’ Oboe dual taper resonators, English shallots, 49 reeds, 61 pipes
Tremulant
Pedal
16’ Subbass wood, 32 pipes
16’ Rohr Gedeckt from Swell
8’ Octave CC–GG# en façade, otherwise 70% tin, 32 pipes
8’ Bourdon extension, Subbass, 12 pipes
8’ Rohr Flute from Swell
4’ Choralbass extension, Octave 8’, 12 pipes
4’ Flute from Swell
16’ Trompette extension to Swell Trompette, 12 pipes
8’ Trompette from Swell
8’ Oboe from Swell
4’ Clarion from Swell