R. J. Brunner name change

Organbuilding in the United States and Canada is a thriving art practiced in hundreds of shops throughout the continent. Emerging from decades of stylistic extremes, organbuilders are combining a wealth of knowledge from the past with new technologies to meet contemporary design challenges. North American builders, compelled by a unique spirit of cooperation and openness, are successfully raising the artistic standards of this time-honored craft. (American Institute of Organbuilders, descriptive statement.)

The organ has occupied a prominent place in the musical culture of Canada since the days of the first European settlement, chiefly because of its close connection with church music and the ambitions of many congregations. The first organs, brought from France, were installed in Québec City around 1660. An anecdotal report mentions the acquisition by a Halifax church of a Spanish instrument that had been seized on board a ship in 1765.1 Following a period in which organs continued to be imported from England and France, organbuilding began as early as 1723 and flourished mainly in Québec and Ontario from the mid-19th century onward.2 By the second half of the 19th century, organ building had become a relatively important industry in Eastern Canada, where companies had acquired sufficient expertise to compete in the international market, including the United States.3

The development of organbuilding in Canada proceeded through several phases, beginning with early builders.4  The first known organbuilder was Richard Coates, who arrived in Canada from England in 1817; he supplied mainly barrel organs to several small churches in Ontario. Joseph Casavant, the first Canadian-born builder, installed his first instrument in the Montréal region in 1840; he transmitted his skills to his sons, who later established the company that achieved world-wide recognition. The arrival from the United States of Samuel Russell Warren in 1836 marked the introduction of professional-calibre organbuilding into the country. His family firm had produced about 350 pipe organs by 1869; it was sold in 1896 to D. W. Karn (see below). Other prominent organ builders included Napoléon Déry (active 1874-1889), Eusèbe Brodeur (a successor to Joseph Casavant in 1866), and Louis Mitchell (active 1861-1893) in Québec, and Edward Lye (active 1864-1919) in Ontario.

The years 1880-1950 were marked by unprecedented growth in organbuilding, beginning with the establishment of Casavant Frères in 1879 in Saint-Hyacinthe, Québec. The Canadian Pipe Organ Company/Compagnie d'orgues canadiennes was established in 1910 by some former Casavant staff, also in Saint-Hyacinthe (when the firm closed in 1931 its equipment was acquired by Casavant). Prominent Ontario builders included the firms of Richard S. Williams (founded 1854 in Toronto), Denis W. Karn (commenced 1897 in Woodstock), C. Franklin Legge (founded 1915 in Toronto, joined by William F. Legge 1919, who later established his own company in Woodstock around 1948), and the Woodstock Pipe Organ Builders (an organization of skilled craftsmen in that Ontario town, 1922-1948). Several smaller, independent builders were active for a time in Ontario, the Maritime provinces, and Manitoba (late 1880s). British Columbia, on the other hand, seems to have had no indigenous organbuilders, for instruments were imported from the United States or from England on ships that sailed around Cape Horn; one of the earliest arrived in Victoria from England by this route in 1861.

In the early 1950s some organbuilders, encouraged by younger organists who had played European instruments, as well as the increasing availability of sound recordings of these organs, turned to classical principles of organbuilding to counter what they perceived as the colorless sound palettes of Canadian organs of the 1930s. The return to earlier tonal aesthetics, inspired by the so-called 17th-century "Baroque organ," found expression in the construction of bright-toned, tracker-action instruments. The "new orthodoxy" was enthusiastically assimilated by Casavant Frères and by a number of independent builders in the same region, some of whom had received their training in Europe. Karl Wilhelm, Hellmuth Wolff, André Guilbault and Guy Thérien, Fernand Létourneau, Gabriel Kney, and Gerhard Brunzema were prominent in this movement, and many of them are still in business. Their accomplishments, along with the activities of other known organbuilders of the 1990s, will be described in chronological order, according to their founding dates, in the remainder of this article.5

Casavant Frères, Saint-Hyacinthe, Québec (1879)

Casavant is the oldest continuing name in organbuilding in North America. Joseph Casavant (1807-1874), the father of the founders of the company, began his organbuilding career while still a Latin student at a Québec religious college, where he completed an unfinished organ from France with the help of a classic treatise on organbuilding. By the time he retired in 1866, after 26 years in business in Saint-Hyacinthe, Québec, he had installed organs in 17 churches in Québec and Ontario, but none of them survive. His sons, Joseph-Claver Casavant (1855-1933) and Samuel-Marie Casavant (1850-1929), worked for Eusèbe Brodeur, their father's successor, for a few years. They opened their own factory in Saint-Hyacinthe, Québec, in 1879, following an extended tour of western Europe inspecting organs and visiting workshops; Claver had apprenticed briefly with a Versailles builder before the tour. In the early years the Casavant brothers were conservative in their tonal design, emulating the ensemble sound of the kind they had heard in old-world instruments that they had examined during their European tour. But from the outset the brothers were innovators, beginning with improvements in the electric operation of their organs in the 1890s. As their reputation spread beyond the cities and towns of their province, production increased steadily.

The company experienced difficult times in the 1930s due to economic conditions, much standardization, and repetitive tonal design. Production was curtailed during the years of World War II due to a shortage of materials, and the company manufactured many unit organs during this period. Later, new initiatives were undertaken by several imaginative artistic directors who served with the firm between 1958 and 1965: Lawrence Phelps from Aeolian-Skinner in the U.S.A.; and European-trained Gerhard Brunzema, Karl Wilhelm, and Hellmuth Wolff.

Most present-day Casavant organs exhibit a conventional design that retains both symphonic and modern elements in subtle synthesis. Casavant organs are recognized for their special tonal qualities and the way the individual stops are blended together into a chorus at all dynamic levels. Time-tested actions include tracker, electrically operated slider windchests, and electro-pneumatic (since 1892; tubular-pneumatic was last used in the mid-1940s). The company workshop has eight departments: metalworking, woodworking, mechanism, consoles, painting, racking, voicing, and assembly. Virtually all components are made in the workshop, including all flue and reed pipes (to 32-foot-length), reed shallots, windchests, consoles, keyboards and pedalboards, and casework, although specialized wood carving and gilding are done by outside artisans. A few electrical components, such as blowers, power-supply units, electromagnets, solid-state combination and coupling systems, and hardware, are purchased from world-wide suppliers. All visual designs are coordinated with their intended surroundings; there are no stock designs. Organs are completely assembled for rigorous testing and playing in preparation for on-time delivery.

The company resumed the construction of tracker-action instruments in 1961 after a lapse of about 55 years, producing 216 such organs since that date. By the end of 1998 the total output amounted to 3,775 organs of all sizes, and many of these have received enthusiastic testimonials from renowned recitalists over the years. Although sales were limited mainly to North America until World War II, Casavant organs now have been installed in churches, concert halls, and teaching institutions on five continents. The firm's largest instrument is a five-manual, 129-stop organ with two consoles installed in Broadway Baptist Church, Fort Worth, Texas, in 1996. The great majority of the very large instruments have been installed in locations in the United States; the exception is the four-manual, 75-stop organ in Jack Singer Concert Hall, Calgary Centre for the Performing Arts, in 1987. The company also engages in renovation projects and additions to existing organs.

The key personnel include Pierre Dionne, President and Chief Operating Officer (from 1978), formerly Dean of Administration at the Business School of the University of Montréal; Stanley Scheer, Vice-President (1984), formerly Professor of Music and Head of the Department of Fine Arts at Pfeiffer University, Misenheimer, North Carolina, holds a Master of Music degree in organ performance from Westminster Choir College, Princeton, New Jersey; Jean-Louis Coignet, Tonal Director (1981), a professionally trained physiologist with a doctorate from the Sorbonne, contributor to music journals, the most knowledgeable authority on the work of Cavaillé-Coll today, was formerly organ expert for the City of Paris; Jacquelin Rochette, Associate Tonal Director (1984), formerly Music Director of Chalmers-Wesley United Church, Québec City, holds a Master's degree in organ performance from Laval University, performs regularly on CBC radio, and has recorded works by several French composers for organ; Denis Blain, Technical Director (1986), with many years of practical experience in virtually all aspects of organbuilding, is in charge of research and development; Pierre Drouin, Chief Engineer, holds a Bachelor of Architecture degree from Laval University, introduced computer-assisted drafting, and supervises the design and layout of each organ. In 1998 the company had 85 full-time employees, many with more than 30 years of service with the company. All levels of management and production personnel function as a team.

Keates-Geissler Pipe Organs, Guelph, Ontario (1945)

The company was established in 1945 in London, Ontario, by Bert Keates (he came from England in his infancy) and relocated to Lucan, Ontario, in 1950. When it was incorporated in 1951 the assets of the Woodstock Pipe Organ Builders (formerly Karn-Warren) were purchased. The company moved to Acton, Ontario, in 1961, a more central location in the province. In 1969 the growing firm took over the business of the J. C. Hallman Company, a manufacturer of electronic instruments and pipe organs, when it discontinued making pipe organs (but not parts for them). For several years some organs were manufactured under the name of Keates-Hallman Pipe Organs.6 The company moved to Guelph, Ontario, in 1994.

Dieter Geissler was born in Dittelsdorf, Saxony, Germany, where he began his trade as a cabinetmaker. At the age of 14 he commenced his apprenticeship with Schuster & Sohn, Zitau, where he remained from 1946 to 1950. In 1951 he moved to Lübeck, West Germany, where he worked as a voicer with E. Kemper & Sohn for five years. In 1956 he moved to Canada to join Keates's staff. When Keates retired at the end of 1971 Dieter Geissler became president of the firm, which he purchased in 1972, and adopted the present company name in 1982. His son, Jens Geissler, joined the company in 1978.

Keates-Geissler organs are offered in all types of action and are custom built to any required size. Altogether, 147 new organs7 have been installed at locations in Canada, the United States (about 15), and Barbados, West Indies. The output includes a number of four- and five-manual instruments; the largest is a five-manual, 231-stop organ, installed in the First Baptist Church, Jackson, Mississippi, in 1992 (a compilation of its original 1939 E. M. Skinner instrument, a 1929 five-manual Casavant organ removed by Keates-Geissler in 1986 from the Royal York Hotel, Toronto, and some additional structures by the company). The firm has undertaken a substantial number of renovation, rebuilding, and reinstallation projects over the years, about 1,500 altogether, about 75 of these in the United States.

All wooden pipes are made in the factory, but metal pipes are made by Giesecke or Laukhuff in Germany to the company's scaling specifications; preliminary voicing is done in the factory before final voicing on-site. The windchests of electro-pneumatic instruments feature Pitman-chest action that includes some unique features to overcome the effects of extremes in temperature and humidity; the company is the only such manufacturer in Ontario and one of a few in Canada. Expandable electronic switching systems are designed and made in the factory from readily available components to facilitate replacement. Solid-state switching and multiple-memory combination actions are also manufactured. Console shells are handcrafted from solid wood in the factory; tracker touch is an available option. Keyboards are custom made to the company's specifications by Laukhuff, Germany, and blowers are acquired mainly from the same company. The company had four full-time employees in 1998; other part-time workers are hired as needed.  

Guilbault-Thérien, Saint-Hyacinthe, Québec (1946)

This company originated with the Providence Organ Company, established in Saint-Hyacinthe in 1946. The partners, André Guilbault, whose father Maurice Guilbault had worked for Casavant, and Guy Thérien, a voicer from Casavant, joined forces in 1968 when the elder Guilbault retired. The present company name was adopted in 1979. When André Guilbault retired in 1992, Alain Guilbault (no relation) acquired an interest in the company.

At the outset the company manufactured electro-pneumatic instruments, but built its first mechanical-action instrument (Opus #1 in a new series), a two-manual, 7-stop organ, in 1970, immediately followed by several small one- and two-manual instruments. From 1974 onward the typical instruments were medium-size, two-manual organs. Larger instruments of three or four manuals began to appear with greater frequency after 1983, the largest being a four-manual, 45-stop organ installed in Grace Church, White Plains, New York, in 1989, the only installation in the United States to that time. While the tonal layout of the organs is mainly inspired by European sources, mainly French, the swell divisions of the larger instruments are sufficiently versatile to handle symphonic literature.

The output of new organs was about 55 to 1998, mainly in Québec and Ontario. The company's work has also involved the restoration and reconstruction of a similar number of Québec organs, mainly by Casavant, but including some of historical significance that are over a hundred years old by such early builders as Napoléon Déry and Louis Mitchell. 

Several compact discs featuring performances by Québec organists on instruments manufactured by the company, or on reconstructed historical Casavant instruments, have been released in the past decade.8

Principal Pipe Organ Company, Woodstock, Ontario (1961)

The company was established by Chris Houthuyzen in Woodstock, Ontario, a town with a continuing tradition of organbuilding. The founder served his apprenticeship and received further training in The Netherlands before coming to Canada. Small to medium-sized instruments, employing electro-pneumatic action, are the company's specialty, with a contemporary emphasis on the guiding principles of Dutch organbuilding. A total of 119 installations have been completed over the years; the largest was a four-manual, 58-rank instrument. Wooden pipes are made in the shop, but most metal pipes come from suppliers in the United States; their scaling is dictated by the acoustics and intended use of the organ. Chests, reservoirs, ducting, consoles, and casework are manufactured on the premises. Much of the company's work involves rebuilding and maintaining organs, as well as the installation and servicing of church bells, including cast and electronic carillons on behalf of the Verdin Company, Cincinnati, Ohio. The company had three employees in 1998.

Gabriel Kney, London, Ontario (1962-1996)

Gabriel Kney was born in Speyer, Germany; his father was a master cabinetmaker and amateur bassoonist, and his mother was a singer. He served his apprenticeship in organbuilding with Paul Sattel in Speyer (1945-1951), where he assisted in the restoration of historic, sometimes war-damaged, instruments, along with new organ construction. Since the era was a time of transition from the "Romantic" style of organbuilding to the concepts of Orgelbewegung, this trend provided him with the opportunity to learn about and participate in the building of organs of both concepts. Concurrently he was a student of organ literature, liturgical music, harmony, and improvisation at The Institute of Church Music in the same city.

He emigrated to Canada in 1951 and joined the Keates Organ Company in Lucan, Ontario, as an organbuilder and voicer. In 1955 he was co-founder, with John Bright, of the Kney and Bright Organ Company in London, Ontario, with the intention of specializing in tracker instruments. The timing was premature, for only a few musicians and teaching institutions found such instruments of interest; with the exception of two teaching organs of tracker design supplied to a college in the United States, most of the early organs were requested to have electric key action. In 1962 Gabriel Kney established his own company in London, Ontario, where, with enlarged facilities and a staff of six to eight, he specialized in mechanical-action instruments. Organs from the period between 1962 and 1966 were designed in the historic manner of Werkprinzip, with organ pipes enclosed in a free-standing casework and separated into tonal sections. The tonal design of smaller instruments followed 18th-century North European practices, with some tuned in unequal temperaments of the period.

Altogether, his shops produced 128 organs since 1955; the largest in Canada being the four-manual, 71-stop, tracker-action instrument with two consoles in Roy Thomson Hall, Toronto. Since the early 1970s almost three-quarters of the installations were in locations in the United States, several of these in large universities. Occasionally maintenance and historic instrument restoration projects were undertaken.

Wooden pipes were made in the shop, with the exception of very large pipes made to specifications by suppliers in the United States, England, or Germany. Metal pipes also were made to order by independent pipemakers in Germany or Holland. Some console components, such as keyboards, were obtained from suppliers in the United States, England, or Germany. Electric switching devices came from the United States in earlier years, later from England. Blowers were imported from Laukhuff in Germany, Meidinger in Switzerland, or White in the United States. All casework and chest construction was done in the shop.

In 1996 Gabriel Kney retired from active organbuilding and closed his company. Since then he has acted as a consultant to churches seeking advice on organ purchase, restoration, and tonal redesign, and sometimes to other organbuilders.

Karl Wilhelm, Mont Saint-Hilaire, Québec (1966)

Karl Wilhelm was born in Lichtenthal, Rumania, and grew up in Weikersheim, Germany. At the age of 16 he entered apprenticeship with A. Laukhuff, Weikersheim (1952-1956), followed by working experience with W. E. Renkewitz, Nehren/Tübingen (1956-1957), and Metzler & Söhne, Dietikon, Switzerland (1957-1960). After moving to Canada, in 1960 he joined Casavant Frères, where he established the department and trained several employees for the production of modern mechanical organs; while there he was responsible for the design and manufacture of 26 organs. In 1966 he established his own firm, first in Saint-Hyacinthe, then moved to new facilities in Mont Saint-Hilaire, near Montréal, Québec, in 1974. For a while he was assisted by Hellmuth Wolff, now an independent builder (see below).

Karl Wilhelm specializes in building mechanical organs of all sizes, 147 to date, of which 69 are located in the United States and two in Seoul, Korea. Of the total output, 43 are one-manual instruments, 93 are two-manual instruments of medium size, and 11 are three-manual instruments--the largest is a 50-stop instrument in St. Andrew's Presbyterian Church, Toronto, installed in 1983. Two have detached consoles, and four have combination actions with electric stop-action; all instruments have mechanical key action. The design and layout of instruments adhere to the principles of the classical tradition of German and French organbuilding. Three-manual instruments feature a large swell division, suitable for the performance of Anglican Church music and the Romantic repertoire.

All wooden pipes are made on the premises, along with almost one-half of the metal pipes that are handmade of a tin-lead alloy; other metal pipes are imported from Germany. Scaling and voicing are done in the classical open-toe manner for natural speech and mellow blend. Windchests and bellows, consoles and action, and cases are manufactured in a 9,000 sq. ft. workshop. Organs may have cases of contemporary design, or perhaps are more ornate with moldings and hand-carved pipe shades that are compatible with the architecture of the location. Blowers are acquired from Laukhuff, Germany; miscellaneous parts come from other suppliers. The firm does not engage in rebuilding or renovation but services and tunes its own instruments throughout North America. In 1998 the firm had five employees, all trained by Karl Wilhelm.

Wolff & Associés, Laval, Québec (1968)

Hellmuth Wolff was born in Zurich, Switzerland. While a teenager he apprenticed with Metzler & Söhne, Dietikon, Switzerland (1953-1957); in his spare time he built his first organ, a four-stop positiv instrument. He received additional training with G. A. C. de Graff, Amsterdam (1958-1960) and with Rieger Orgelbau, Schwarzach, Austria (1960-1962). In the United States (1962-1963) he worked with Otto Hofmann, in Austin, Texas, and Charles Fisk, in Gloucester, Massachusetts. After moving to Canada he worked with Casavant Frères (1963-1965) in its newly established tracker-action department, and then with Karl Wilhelm (1966-1968), with whom he had worked at Casavant. In the interval 1965-1966 he returned briefly to Europe to work as a designer and voicer with Manufacture d'orgues Genève, in Geneva. Besides playing the piano and singing in choirs wherever he went, he completed his musical training by taking organ lessons with Win Dalm in Amsterdam and later with Bernard Lagacé in Montréal.

In 1968 he opened his own business in Laval, Québec, with one employee; his present associate, James Louder, started his apprenticeship with Hellmuth Wolff in 1974, after training in classical guitar and English. The first large project undertaken in that year was the construction of a three-manual, 26-stop instrument at the Church of St. John the Evangelist, New York City; this was one of the city's first modern tracker-action organs and it incorporated features not yet seen in North America. In 1977 the company moved to a new shop; the firm became incorporated in 1981, and James Louder became a partner in 1988.

Hellmuth Wolff has been part of the Organ Reform in North America since the movement came to this continent in the early 1960s. He specializes in mechanical-action instruments, large and small, whose design is inspired by French or German classical traditions, although other styles are represented that are designed to accommodate a wide range of organ literature. A total of 42 organs have been manufactured; about one-half of these were installed in locations in the United States. While a few small residence or practice instruments have been built, the majority are two-manual organs, in addition to eight three-manual organs, and one four-manual, 50-stop/70-rank instrument installed in Christ Church Cathedral, Indianapolis, Indiana, in 1989.9 Other related activities include rebuilding, restoration, and maintenance work, chiefly in the Montréal area.

Wooden pipes are made on the premises, while metal pipes are acquired from several pipemakers in Canada, U.S.A., and Europe; some reeds are made there, also. Windchests, consoles, and cases are also manufactured on site. Blowers are acquired from Meidinger and Laukhuff in Germany. Several installations feature both mechanical stop-action and capture systems; the first was built in 1977 for the Eighth Church of Christ, Scientist, in New York City; it was probably the first such system in North America. Both sequencers and traditional multilevel capture systems are used. There were eight employees in 1998.

Hellmuth Wolff, along with his associate, James Louder, have contributed to symposiums and written publications on organs and organbuilding.10 Fourteen compact discs, featuring performances by Canadian and American artists on Wolff instruments, have been released, and three others are in preparation.11

Brunzema Organs, Fergus, Ontario (1979-1992)

Gerhard Brunzema was born in Emden, Germany, and grew up in Menden on the Ruhr river, a northern part of the country where there was an abundance of historic organs. After World War II he apprenticed with Paul Ott in Göttingen and worked with him as a journeyman organbuilder (1948-1952). He received extensive technical training, including acoustics, at the Brunswick State Institute for Physics and Technology (1953-1954), and received a Master's degree in organbuilding in 1955. In 1953 he joined the prominent European organbuilder Jürgen Ahrend in the construction and restoration of organs, some in Holland and Germany of great historical significance; this association continued for 18 years. After emigrating to Canada he joined Casavant Frères in 1972 and served as artistic director until 1979; during that time he was responsible for the design of several notable organs in Canada, the United States, Japan, and Australia, along with the restoration of a number of historic Casavant instruments in Ontario and Québec. His experience at Casavant gave him the opportunity to work with very large organs, an experience that was lacking in Germany.

In 1979 he established his own business in Fergus, Ontario. Throughout his career he specialized mainly in small, one-manual, four-stop, continuo organs (25 in all); most of his nine two-manual instruments--the largest was 25 stops--were made between 1985 and 1987. In 1990 he was joined by his son, Friedrich, who had completed his apprenticeship in Europe. Until the time of his death in 1992, Gerhard Brunzema's total output amounted to 41 instruments; of these, 20 were installed in Canadian locations (mainly in eastern provinces), 17 in the United States, one in the Philippines, one in South Korea, and two in European countries. The tonal design of his instruments was strongly influenced by Schnitger organs that he had studied and restored while in Europe. He believed that basic organ design cannot be learned through restoration work, because such instruments were conceived by others; nevertheless, in restorations the intentions of the original builders should be respected. As for new instruments, his philosophy was that "An organbuilder should choose a style and stay with it, so that he not only continues to develop his own skills, but also continues to help improve the skills of the people working for him. . . . Become a master of one thing, get over the initial difficulties very quickly, and then polish your knowledge, the details of which will finally add up to a very good result."12

Koppejan Pipe Organs, Chilliwack, British Columbia (1979)

Adrian Koppejan was born in Veenendaal, Holland, and apprenticed with his father, who was an organbuilder there. He worked with Friedrich Weigle in Echterdingen by Stuttgart, Germany (1963-1966), with Pels & Van Leeuwen in Alkmaar, Holland (1968-1972) as shop foreman of the mechanical organ department, and with his father's company, Koppejan Pipe Organs, in Ederveen, Holland (1968-1972). He moved to Canada in 1974 and established his own company five years later.

Adrian Koppejan strives for a clear, warm, but not loud sound in his instruments, a preference inspired by classical organs of North Germany. This sound palette is reflected in the instruments in which he specializes: small and medium-size tracker instruments; he has built five electromechanical organs, as well. His output to date consists of 19 organs; these have been installed in churches and private residences in British Columbia, Alberta, and Washington state. His largest organ is a three-manual, 31-stop, electromechanical instrument, with a MIDI system, installed in the Good Shepherd Church, White Rock, B.C., in 1995. An instrument of similar size was constructed in 1998. Rebuilding, restoration, maintenance, and tuning are also part of regular activities.

Wooden pipes are mostly acquired from Laukhuff, Germany; metal pipes come from Stinkens in Holland and Laukhuff in Germany. Keyboards are made in Germany by Laukhuff or Heuss. Winding mechanisms, consoles, solid oak cabinets, and casework are manufactured in the shop. Blowers are supplied by Laukhuff, and electrical control systems come from Peterson in the U.S.A. There were two part-time employees in 1998 as Adrian Koppejan reduced the scope of his operations in anticipation of retirement.

Orgues Létourneau,  Saint-Hyacinthe, Québec (1979)

Fernand Létourneau was born in Saint-Hyacinthe, Québec, where he worked for while as a carpenter before entering employment with Casavant Frères in 1965; there he apprenticed with his uncle, Jean-Paul Létourneau, who was head reed voicer. He remained with the company for 14 years, where he was head voicer from 1975 to 1978, when he decided to set up his own independent company. First, with the help of a Canada Council grant, he embarked on an organ tour of Europe to study the voicing of old masters. Upon his return to Canada in 1978 he began building organs in Sainte-Rosalie, Québec, and became incorporated in 1979. His first organ, a two-manual, 6-stop instrument, was started in the basement of the family house and then displayed in the shop of a cabinetmaker; it was later acquired by the Conservatoire de Musique du Québec, Hull, where dozens of students have learned to play the organ on this small instrument. In 1984 he moved back to Saint-Hyacinthe, where three other organbuilders were already established. The factory's first building was formerly a municipal water-filter plant; the partially underground space provided a room 35 feet in height, ideal for erecting organs. A second industrial building was acquired recently to supplement the original premises.

A total of 55 organs of various sizes have been built to 1998; 13 others are in progress. The great majority have mechanical action, utilizing classical principles used in European instruments, and with the flexibility provided by ranks inspired by Dom Bédos, Schnitger, and Cavaillé-Coll. The largest will be a four-manual, 101-stop, mechanical-action instrument intended for the Francis Winspear Centre, Edmonton, Alberta. International distribution has been common from the outset, beginning with three early instruments that were installed in Australian locations in the early 1980s (the builder had become known on account of his activities as a voicer of Casavant instruments in that country). Others have been placed in New Zealand, Austria, England (Pembroke College, Oxford, 1995; an instrument is under construction for the Tower of London for completion in late 1999), the United States (over one-third of the total production), and Canada (chiefly eastern provinces, a few in the west). The company now has permanent representatives in the United States, England, and New Zealand. Fernand Létourneau prefers to build instruments of eclectic tonal design that are suitable for the performance of a wide range of organ literature. Historic restorations have also been undertaken.

All organ components, with the exception of electronics, are made in the factory, including wooden and metal pipes to 32-foot length, keyboards, consoles, and casework. Blowers are acquired from Laukhuff, Germany. Middle-size organs are equipped with electronic sequencers, card readers, and similar devices. The company is constantly engaged in rebuilding and restoring instruments of different vintages to original condition, about 50 to date, several of which have been designated as historical or heritage instruments. In 1998 there were 45 full-time staff in the Létourneau "family," of which a number are related to one another as father-son/daughter, uncle, brother, cousin, and husband-wife.  

Raymond J. Brunner founded R. J. Brunner & Co. in 1981. He is a graduate of Lehigh University and a member of the American Institute of Organbuilders and the Organ Historical Society.

Restoration of the 1770 Tannenberg  organ at Zion Moselem Lutheran Church, Moselem Springs, Pennsylvania, was completed in September 2011 by R. J. Brunner & Co. of Silver Spring, Pennsylvania. The earliest of the nine extant David Tannenberg organs, it predates the Revolutionary War and is perhaps the oldest surviving organ built in the American colonies. As such, it is of great historic importance, and its restoration allows us to learn more about 18th-century organbuilding as practiced by Tannenberg and other German immigrants to Pennsylvania.

Tannenberg was a Moravian and built many organs for Moravian congregations in Pennsylvania and elsewhere. He also supplied organs to Lutheran, German Reformed, and Catholic congregations. His instruments ranged in size from four-stop positive organs for Moravian use to a large three-manual, 34-stop organ for Zion Lutheran Church in Philadelphia. Tannenberg’s Moravian organs had a predominance of unison-pitch stops, since those organs were generally used in conjunction with other instruments. His Lutheran organs had more developed choruses that might include mutation and mixture stops, as well as reeds. The Moselem organ has eight stops on one manual, with a total of nine ranks. Built early in Tannenberg’s career, it provides an opportunity to learn more about the evolution of his organbuilding. It is the only surviving example of his organs with a walnut case.   

The Moselem organ was completed in 1770 and installed in the stone Zion Lutheran Church building, where it was located in a small gallery. This building was replaced by a new brick structure in 1894, at which time the organ was moved and rebuilt by Samuel Bohler of Reading, Pennsylvania. Bohler replaced the original bellows with an internal winding system and replaced the keydesk and keyboard. He altered the stop action and also removed the Terz and Mixtur stops, replacing them with lower-pitched unison stops. By then the walnut casework had been painted over. The casework was eventually painted white, imitating the appearance of other Tannenberg organs.  

In 2010, R. J. Brunner & Co. was chosen to undertake a historic restoration of the organ. Organbuilder Raymond Brunner was in charge of the project, and his previous research and restoration experience with several other Tannenberg organs was a valuable asset to determining how the work should be done. It was decided to restore the organ to its original form, including replacement of the two missing original stops and construction of an authentic winding system. Fortunately, the unaltered 8-stop Tannenberg organ at Hebron Lutheran Church in Madison, Virginia provided many of the answers. Although built 32 years later, it has an original pair of wedge bellows that could be copied for the restoration. Another fortunate event was that Brunner was able to obtain parts of two different period wedge bellows sets, once used on Pennsylvania German organs that are no longer extant. Using these historic fragments from other organs enabled the recreation of an authentic set of bellows like the original winding of the organ. An electric blower provides an alternate source of wind.

Twenty-five pipes of the Principal 8′ and ten pipes of the Principal Octav 4′ are in the façade. The Flaut Major 8′ and Flaut Minor 4′ are identical open wood ranks made primarily from pine and walnut. The rack board for the Terz shows that this rank did not contain a break. 

The restoration required making a new keydesk and stop action, as well as a new keyboard. The keyboard was copied from the Madison instrument, with the natural keys covered with ebony, while the walnut sharps are capped with reclaimed ivory from old keyboards. Removal of several layers of paint revealed the beauty of the walnut casework and the fine quality of this master organbuilder’s work. The façade pipes were restored to their original appearance by removal of ears that had been applied when Bohler rebuilt the organ. A metallurgical analysis of the pipe metal was done to determine the proportions of lead and tin, as well as the amount of impurities in the metal. New Terz and Mixtur pipes were made for the organ by the Paul Fritts shop in Tacoma, Washington. Restoration of the original pipes and voicing of the new pipes was done by Hans Herr in the Brunner shop.   

The organ was re-dedicated on October 2, 2011 with a concert played by Philip T. D. Cooper; it was hand pumped for the entire concert. Mr. Cooper also assisted in historical research for the restoration and was instrumental in encouraging the church to undertake the project. The fine sound of the organ delighted the large crowd in attendance, and Zion’s organist Nancy Keller has been using the organ on a regular basis. This instrument should serve the congregation of Zion Moselem Lutheran Church well for many more years, and the organ can be heard once again as David Tannenberg intended.

Three Decades of Building Organs in Lake City, Iowa

John A. Panning is tonal director of Dobson Pipe Organ Builders. A native of Wisconsin, he worked for two years with Hammes-Foxe Organs, Inc. in the Milwaukee area prior to joining Dobson in 1984. In these twenty years, he has been involved in every facet of pipe organ design, construction and maintenance. Mr. Panning has served two terms as Secretary of the American Institute of Organbuilders, and is currently a member of the AIO Journal committee. He was a member of the National Council of the Organ Historical Society from 1985–1991, and has served on two OHS convention committees. He has been North American Editor of Publications for the International Society of Organbuilders since 1991.

Thirty years ago this month, Lynn Dobson opened an organ building workshop in Lake City. Three decades later, clients from near and far have made the journey to this small western Iowa town.

Lynn A. Dobson, founder of the Dobson Pipe Organ Builders, was born in Carroll, Iowa, in 1949, and grew up on a farm in nearby Lanesboro. In 1966, he received a scholarship from the Hill Foundation to attend the Minneapolis School of Art summer session for gifted students. He graduated from Wayne State College in Wayne, Nebraska, in 1971 with majors in art and industrial education. During his college years, he built a twelve-stop mechanical-action organ in a shed on the family farm; this organ, Op. 1 (II/15), was eventually sold to Our Savior’s Lutheran Church in Sioux City, Iowa, where it still serves today. Upon graduation, Dobson taught high school art in Plattsmouth, Nebraska. However, the desire to be involved with organ building persisted, and in 1974 he left teaching to work for the Hendrickson Organ Company of St. Peter, Minnesota. In November 1974, he established his own firm, opening a small shop at 120 West Main Street in Lake City, Iowa.

What follows is a chronicle of the more important dates in the company’s history, a big-picture overview of three decades of art and craft as practiced by an increasingly prominent Midwestern American organ builder.

1975 ~ The young company’s first contract comes from one of Dobson’s former teachers, Antony Garlick, a music professor and composer at Wayne State College. The ten-stop residence organ incorporates both new and revoiced pipework. When Garlick moved in 1986, he sold the organ to Mary Brooks of Doylestown, Pennsylvania. In 1998, she in turn sold it to The Church of the Holy Spirit in Harleysville, Pennsylvania, and Dobson was once again called upon to move the organ, making several additions to suit its new, larger home. In his first year of business, Dobson is accepted as a member of the American Institute of Organbuilders (AIO).

1976 ~ Olivet Congregational Church, St. Paul, Minnesota, signs a contract for Op. 4 (II/33). The organ’s donor gave his gift to the church on the condition that it help launch the business of a promising young organ builder. At this time Lynn Dobson was assisted by his father Elmer Dobson, Jon Thieszen, who first began as summer help during college and would later become the company’s technical designer, and voicer Robert Sperling, a former co-worker at Hendrickson. The resulting instrument is a monumental achievement for so young a firm.

1979 ~ The company moves to its current location at 200 North Illinois Street, completely renovating the historic building and adding an erecting room with a 30¢ ceiling. In addition to instruments built for area churches, Dobson receives commissions from two Minnesota colleges as the decade closes. The first is a small studio organ for St. Olaf College (Op. 8, II/7; 1978). The second Minnesota institution, Bethany Lutheran College in Mankato, commissions an organ for its chapel (Op. 10, II/21; 1979), located in the school’s historic Old Main building. Op. 10 enjoys wide attention in organ journals. In 1996 it undergoes some tonal additions (increasing its size to 24 ranks) and receives a dramatic revision to its case to better suit its second home, Bethany’s new Trinity Chapel.

1980 ~ The decade opens with larger and more diverse projects, including one less than a block from the original Main Street shop: Lake City Union Church purchases a two-manual instrument (Op. 13, II/29; 1980). Dobson is engaged by Westminster Presbyterian Church of Des Moines, Iowa, to complete the organ (Op. 14, II/38; 1981) left unfinished by Lawrence Phelps Associates after that firm’s insolvency. Nearby Iowa State University in Ames, Iowa, contracts for a practice organ (Op. 16, II/3; 1981) and a teaching studio organ (Op. 21, II/18; 1982). The capabilities of the shop were enlarged during this period by several new employees, among them Tom Kult, a skilled cabinetmaker who later becomes shop foreman; David Storey, an organ builder who had previously worked for Jim McFarland in Pennsylvania; and Lake City native Sally Winter, secretary. Robert Sperling becomes full-time voicer. The firm is accepted for membership in the International Society of Organbuilders and is invited to join the Associated Pipe Organ Builders of America (APOBA); Lynn Dobson is elected to the AIO Board of Directors.

1983 ~ The completion of large two-manual organs for the Church of St. Michael in Stillwater, Minnesota (Op. 23, II/34; 1983) and First Presbyterian Church in Manhattan, Kansas (Op. 24, II/43; 1983) are harbingers of Dobson’s expansion into the rest of the country. Op. 24 is the largest organ built by the firm to date, and is the first organ in the United States to employ a “dual” stop action, one that can be operated mechanically by the organist as well as electrically through a solid-state combination action.

1984 ~ John Panning, an organ builder from Wisconsin, joins the crew this year; he is later appointed the firm’s tonal director. The shop is remodeled and enlarged at this time to accommodate the fabrication of mechanical key action parts and console chassis. In November, the firm celebrates its 10th anniversary with an open house and a recital by Guy Bovet on Op. 13 at Lake City Union Church; hundreds of clients and friends of the company attend.

1985 ~ Op. 28 (II/30; 1985), for The Church of the Holy Comforter in Burlington, North Carolina, is the first of many Dobson instruments to be located outside of the Midwest. From 1985 to 1990, the firm builds twenty new organs in Pennsylvania, New York, North Carolina and Virginia, in addition to five Midwestern states. Eight are for universities and colleges, of which five are institutions affiliated with church bodies: Bethel College, North Newton, Kansas (Op. 27, II/19; 1985), St. Olaf College, Northfield, Minnesota (Op. 29, II/30; 1985), Augsburg College, Minneapolis, Minnesota (Op. 42, III/44; 1988), Calvin College, Grand Rapids, Michigan (Op. 44, III/49; 1989), and Wartburg Theological Seminary, Dubuque, Iowa (Op. 46, II/15; 1989). Op. 42 and 44 are both for new college chapels designed in cooperation with Dobson. New shop personnel by the end of this decade include Meridith Sperling (pipe racking, general organ building), Lyndon Evans and Randy Hausman (cabinetmakers), Dean Heim (general organ building, and later shop foreman), Art Middleton (key action and consoles) and Bob Savage (leatherwork and electrical). Dobson hosts the annual spring meeting of APOBA, during which the firm is elected president.

1989 ~ The first AIO Midyear Seminar is held at the Dobson shop. Twenty organ builders from across the country participate in lectures on case design and construction, cost accounting, shop administration and equipment. By this time the firm is well known for its artistic and innovative organ case design.

1990 ~ Gradual evolution of the firm’s tonal style continues. Although specialized instruments such as the organ in Italian style for Indiana University (Op. 35, II/26; 1987) have been built, most are of eclectic design. Earlier instruments explored the neo-classic aesthetic; new projects blend both classical and romantic influences. Op. 44 (1989) at Calvin College includes a 16¢ Open Wood in the Pedal, two enclosed divisions and a rich, smooth tonal palette. Joining the firm this year are Kirk Russell (business manager) and Dean Zenor, an organ builder from Connecticut.

1992 ~ Two instruments built this year demonstrate the firm’s range. Op. 55 (II/32) for St. John Lutheran Church in Storm Lake, Iowa, features Kirnberger III tuning, dual wind systems (a wedge bellows for flexible wind, a parallel-rise bellows and wind stabilizers for steady wind) and a freestanding case with attached console at the rear of the church. The chancel location and Anglican church music emphasis of St. Luke’s Episcopal Church, Kalamazoo, Michigan, result in Op. 57’s (II/42) more romantic tonal design. Op. 56 (II/17), for Trinity Lutheran Church, Manhattan Beach, California, is the first Dobson installation on the West Coast. The firm is incorporated as Dobson Pipe Organ Builders, Ltd., a new 4,500 sq. ft. wood shop is built, and a pipe shop is set up. The company becomes a prize sponsor for the National Improvisation Competition of the American Guild of Organists.

1993 ~ Op. 60 (III/49) for First United Methodist Church, Mesa, Arizona, the firm’s seventh three-manual instrument, features a Solo as the third manual rather than a more customary Positive or Choir. Voiced on 6≤ wind pressure with mechanical action, this division includes an 8¢ Harmonic Flute, 4¢ Flute Octaviante, Cornet V, and 8¢ Bombarde, all under expression except for the Cornet, which is mounted outside the Solo enclosure.

1995 ~ The mid-’90s see an even wider variety of projects, ranging from Op. 62 (II/11; 1994), a residence organ for Rich Wanner in Berkeley, California, to the 1996 renovation of the important four-manual 1959 Schlicker organ at Valparaiso University, Valparaiso, Indiana, and its enlargement to 102 ranks. Other notable organs delivered are Op. 65 (II/36; 1995) for the University of South Carolina, Columbia, South Carolina, Op. 67 (II/32; 1996) for Wartburg College, Waverly, Iowa, and Op. 69 (II/31; 1997) for Pakachoag Church, Auburn, Massachusetts. Voicer and pipemaker William Ayers joins the firm during these years.

1998 ~ The organ for St. Paul’s Episcopal Church in Minneapolis, Minnesota, (Op. 70, II/45) unabashedly combines classical and romantic tonal elements in a fresh and original way. This same line is followed in the large three-manual instrument for West Market Street Methodist Church in Greensboro, North Carolina (Op. 71, III/58; 1999), voiced in collaboration with Los Angeles organ builder Manuel Rosales. A somewhat more classical course is taken with the instrument at St. Joseph Abbey in St. Benedict, Louisiana (Op. 73, III/38; 2000), which is greatly enhanced by the Abbey church’s five seconds of reverberation. Joining the firm by the end of the decade are Scott Hicks (general organ building), Gerrid Otto (windchests, general organ building), John Ourensma (voicing, pipemaking) and Randall Pepe (wood pipemaking and general organ building).

2000 ~ The firm’s work at the beginning of a new century includes the monumental instrument for the Cathedral of Our Lady of the Angels in Los Angeles, California (Op. 75, IV/105; 2003) and the company’s first contract for a major concert hall, Verizon Hall in Philadelphia’s Kimmel Center for the Performing Arts (Op. 76, IV/125; 2006), the new home of the Philadelphia Orchestra. These high-profile projects bring Dobson into collegial working relationships with world-famous architects: José Rafael Moneo for the cathedral project and Rafael Viñoly for the concert hall.

2003 ~ Not to be lost among the contracts for immense organs are instruments of more normal size delivered to churches and universities in Delaware, Illinois, and Minnesota. Op. 78 (III/42) for St. John’s Methodist Church in Augusta is Dobson’s first instrument in Georgia, housed in an elegant cherrywood case with carved pipeshades. Joining the firm during the first years of the century are Antal Kozma (technical design) and Donny Hobbs (general organ building, voicing, pipemaking).

2004 ~ Op. 80 (II/26), for St. Paul’s Church, Rock Creek Parish, Washington, D.C., was set up and played in Lake City during a 30th anniversary open house. To further celebrate, a festive reception for friends of the company was held during the Los Angeles AGO convention following Martin Jean’s recital on Op. 75 at the Cathedral of Our Lady of the Angels. The second phase of the installation of Op. 76 (IV/125) in Verizon Hall takes place during the summer, while Op. 79 (II/23), for Shepherd of the Bay Lutheran Church, Ellison Bay, Wisconsin, is installed in the fall. Ongoing design work includes a significant concert hall instrument for the new Atlanta Symphony Center, designed by famed architect Santiago Calatrava of Zürich. Instruments for the Chapel of the Cross in Chapel Hill, North Carolina, and the Lutheran Church of the Good Shepherd in Lancaster, Pennsylvania, give the shop a small respite between these large projects.

Since 1994, the daily operation of the shop has been under the direction of a management team consisting of Lynn Dobson (president and artistic director), John Panning (tonal director), Jon Thieszen (technical designer), Dean Heim (shop foreman), Dean Zenor (project manager) and Kirk Russell (business manager).

News, specifications of every organ, and many photographs can be found on Dobson’s website at

<www.dobsonorgan.com&gt;.

Dobson Pipe Organ Builders, Ltd.

William Ayers, 1994, voicer, pipemaker

Mitch Clark, 2004, technical designer

Lynn A. Dobson, 1974, president and artistic director

Lyndon Evans, 1988, cabinetmaker

Randy Hausman, 1988, cabinetmaker

Dean Heim, 1988, shop foreman, general organbuilding

Scott Hicks, 1997, general organbuilding

Donny Hobbs, 2003, general organbuilding, voicing

Antal Kozma, 2001, technical designer

Arthur Middleton, 1987, machinist, key action, wood pipes

Gerrid D. Otto, 1998, windchests, general organbuilding

John Ourensma, 1999, voicer, pipemaker

John A. Panning, 1984, tonal director, voicer

Kirk P. Russell, 1990, business manager

Robert Savage, 1989, leatherwork, electrical, general organbuilding

Meridith Sperling, 1985, windchests, general organbuilding

Jon H. Thieszen, 1975, technical designer

Sally J. Winter, 1983, accounting and secretarial

Dean C. Zenor, 1990, key action, administrative

Grant Smalley Pipe Organs, Victoria, British Columbia (1984)

Born in Sidney, near Victoria B.C., Grant Smalley has worked as an organbuilder since 1966. He was associated with Gabriel Kney from 1968 to 1979, primarily building tracker-action organs and installing them throughout Canada and the U.S.A. During the last eight of those years he assumed Kney's tuning and maintenance business in addition to his organbuilding duties. He returned to Victoria in 1980 and established his own business four years later, buying out the organ maintenance service of Hugo Spilker, who had done restorations in the area. His associate, Douglas Adams, received formal training in instrumentation and systems technology, and manufacturing engineering technology; in addition to assisting in the construction of the new shop, he is responsible for electrical design, construction, and mechanical work. Beverly Smalley, the wife of Grant Smalley, handles the business and financial operations. All three are active participants in community choral groups.

Grant Smalley has built several small organs: a four-stop positiv organ, mechanical action (1985); a four-stop, portable, continuo organ with 56-note transposing keyboard, mechanical action (1989); and two continuo organs of 31/2 and 41/2 ranks, both with mechanical action (1995, 1997). The major activity, however, is organ restoration, along with regular tuning and routine maintenance work: about 50 organs throughout Vancouver Island and Greater Vancouver. A number of heritage organs in Victoria, including several instruments built by Casavant Frères in the early 1900s, and others by English and American makers, have received extensive overhauls in recent years.

Wooden pipes, most windchests, consoles, and casework are built in the shop; metal pipes are ordered to specifications and voiced there. Other components acquired from suppliers include keyboards, drawknobs, switching systems, and blowers.

Blair Batty & Associates, Simcoe, Ontario (1985)

Blair Batty was born in Simcoe, and as a teenage organ player he acquired an interest in the mechanical workings of organs. His organbuilding career began with the Keates Organ Company, Acton, Ontario, where he learned windchest construction, wiring, tuning, and installation procedures. In 1976 he moved to Europe, where he learned the craft of metal pipemaking with Jacques Stin-

kens, Zeist, Holland, and the art of reed manufacturing with Carl Giesecke & Sohn, Göttingen, West Germany. During that period he travelled extensively throughout Europe to study examples of French, German, and Dutch organbuilding. In 1977 he went to Gloucester, Massachusetts, to join C. B. Fisk as a pipemaker and draftsman, then in 1979 he was invited to head the pipe shop of the Noack Organ Company, Georgetown, Massachusetts. In 1981 he returned to Canada to work for Brunzema Organs, Fergus, Ontario, then returned to Simcoe in 1985 to establish his own firm. Since then he has visited England on several occasions to study the instruments of Willis and Hill.

The company has built three new organs. One is a two-manual, 27-stop instrument of eclectic design incorporating Schnitger-inspired choruses, a French-character trumpet, and Dutch/French-style Swell mutations, with console-equipped MIDI (1991). Another is a two-manual, 19-stop instrument of British-inspired design in which the basic choruses follow William Hill, but includes a Schnitger-style trumpet, a cornet and mutations of classical French design, and string stops scaled and voiced on Cavaillé-Coll principles (1993). A four-rank box organ was built for a private customer.

The company specializes in restoring and rebuilding older organs, employing the techniques and materials of the original builder as far as possible, and provides tuning and maintenance service to about 100 churches annually throughout southwestern Ontario. Most of the components of organs are produced in the factory: Pitman and slider windchests, bellows, rollerboards, tremulants, keyboards and pedalboards, and consoles. Pipes, both wooden and metal (including reeds), are generally made on the premises; the metal pipeshop and foundry section has a 12-foot, polished granite casting table, one of the few in Canada. Blowers and electrical combination and switching actions are acquired from external suppliers. The firm also provides services, parts, and pipes to other builders and tuners. A large reference library of historical and current organ design data, including pipe scalings of hundreds of historic organs, is maintained. A computer-assisted design (CAD) system is used. The firm had three full-time employees and several part-time helpers in 1998.

Gober Organs, Toronto, Ontario (1985)

Halbert Gober was born in Austin, Texas, and began his organbuilding career with Otto Hofmann (1969-1972), an organbuilder in Austin known as an early proponent of the tracker revival. Following university studies in liberal arts and architecture, he lived in Germany from 1972 to 1980. During the first four years he studied music, architecture, and organbuilding; in the remaining years he was employed with various organbuilders, including Rensch in Lauffen-am-Neckar (1972); Jann (1977-1980), where he completed his formal apprenticeship in 1979; and Felsberg in Chur, Switzerland. Following his move to Canada in 1981 he was employed as a voicer with Karl Wilhelm until 1985, before opening his own shop in the Montréal area in that year. From there he served as a freelance voicer and pipemaker for several organbuilders in North America and Europe.

He established his own shop in Toronto in 1991, where he commenced building tracker-action organs. Output to date amounts to six two-manual instruments of medium or small size; the most recent of these is a five-stop studio organ for the University of Notre Dame, South Bend, Indiana. Rebuilds and tonal revision projects are also undertaken. His philosophy is to draw on the full heritage of historical organbuilding in the construction of cohesive and logical instruments, with equal priority to dependability and musicality.

Wooden pipes, along with metal pipes made of cast and hammered lead, are manufactured on the premises. Reed pipes, including shallots, are also made in the shop. Action parts are from Germany. There were three employees in 1998. 

Pole & Kingham, Chatham, Ontario (1985)

 Donald Pole and Ron Kingham founded their company in 1979 and then incorporated in 1985, when the construction of complete new organs commenced. Earlier, between 1966 and 1968, Ron Kingham had been an employee of John Bright, a co-founder with Gabriel Kney of the Kney & Bright Organ Company in 1955; he built a house organ under John Bright's supervision. In the first five years of their association, the partners' work was limited to tuning, repairs, cleaning, and general maintenance.

Since 1985 they have built and installed seven new electrical-action instruments (two incorporating some older parts), mostly of medium-size, all in Ontario churches; two other instruments were provided to churches in Michigan, U.S.A. While their instruments are designed to meet both liturgical and performance needs, recent organs have a Romantic bias, and the Symphonic era is recalled in a new, three-manual, 36-stop instrument (the largest to date), with its six-rank String Organ division, installed in Holy Trinity Anglican Church, in Chatham, Ontario, in 1997. Other services include restoration of both tracker- and pneumatic-action organs, rebuilding with solid-state switching, enlargement, and tonal additions, along with general maintenance and tuning.

Wooden pipes (Bourdon, Chimney Flute, Gedeckt, and Doppelflute--the latter scaled after a fine Karn stop), windchests and reservoirs, and consoles are made in the shop; metal pipes are obtained from suppliers in Canada, U.S.A., Germany, and Holland. Five employees worked with the partners in 1998.

Juget-Sinclair, Montréal, Québec (1994)

Denis Juget, a native of the Savoy region of France, received his diploma in fine cabinetmaking in Annency, Haute-Savoy, France, in 1979, then worked as an apprentice with leading organbuilders on both sides of the Atlantic, with whom he acquired skills in all phases of organbuilding: Lucien Simon, Lyon, France (1979-1983); Robert Chauvin, Dax, France (1983-

1985); Wolff & Associés, Laval, Québec, upon his arrival in Canada (1985-1991); Orgelbau Goll, Lucerne, Switzerland (1990-1991); Orgelbau Rohlf, Seitzental, Germany (1992-1994); and Karl Wilhelm, Mont Saint-Hilaire, Québec (1992-1994). Special assignments be-tween 1988 and 1990 involved the restoration, renovation, and voicing of several organs in Austria, Italy, and Spain. His organbuilding enterprise began in 1994 in Saint-Basile-le-Grand, Québec, in a backyard, two-story, former chicken coop, which was converted into a workshop. In the following year he completed a two-manual, 3-stop house organ for a private client.

Following studies in science at McGill University in Montréal, Stephen Sinclair worked first as an apprentice cabinetmaker, then as an apprentice organbuilder with Wolff & Associés (1989-1991). He received practical working experience in general organbuilding and reed-stop restoration with Manufacture d'orgues Franc-comptoise, Courtefontaine, France (1995, 1997); pipemaking with Georges Blaison, France (1996) and N. P. Mander, London, England (1997); and general organbuilding, design, voicing, maintenance, and tuning with Wolff & Associés (1992-1998). He joined Denis Juget as an equal associate in 1998.

The company divides its time between the restoration of historic instruments and the construction of small mechanical-action organs. Since 1995 five two-manual, 3-stop, house organs and one continuo organ have been manufactured; three of the house organs for clients in the United States. Works in progress include two similar house organs for destinations in Québec and Germany, and a two-manual, 10-stop practice organ for the University of Cincinnati, ready in 1999. The house organs incorporate a design by Denis Juget that enables them to be moved relatively easily without breaking down the action.

All parts are made in-house, including wooden and metal pipes, wind chests, bellows, rollerboards, keyboards and pedalboards, drawknobs, and casework (hand-planed in solid wood, using mortise-and-tenon construction). Blowers are purchased from Laukhuff, Germany. Several part-time workers assist in various stages of production and installation. Following relocation in late 1998 to an industrial space with 30-foot cathedral ceilings in Montréal, the associates intend to make the leap from building practice instruments to full-fledged church organs in the near future.

D. Leslie Smith, Fergus, Ontario (1996)

Leslie Smith grew up in southern Alberta, and acquired his interest in music at an early age through involvement in church choirs and piano lessons. He developed an early fascination with organ building and enrolled in organ performance studies at the University of Calgary after completing high school. Using practical skills acquired from his father, who was a carpenter and mechanic, he completed several kits for harpsichords and clavichords, and established an association with a local organ serviceman who introduced him to the techniques of maintaining and tuning electro-pneumatic instruments. In 1973 he moved to London, Ontario, to continue his organ studies at the University of Western Ontario. While in that city, he became acquainted with Gabriel Kney, in whose organbuilding shop he worked on a part-time basis for several years. In 1982 he joined Brunzema Organs in Fergus, Ontario, where he remained for 10 years as a journeyman organbuilder. After the death of Gerhard Brunzema in 1992 and the closing of his organbuilding operation, Leslie Smith worked as an independent contractor in pipemaking and voicing on a number of projects in Canada and the United States. His first organ, a two-manual, 11-stop studio organ was undertaken in 1982 as a part-time project while working with Gerhard Brunzema; it was completed in 1992.

In 1996 he established his new workshop on part of the former Brunzema premises. In the same year he produced his first commission, a one-manual, 6-stop, mechanical-action organ, for a cemetery chapel in Montréal. A similar organ, but without pedals, was supplied to a church in Kansas City, Missouri. Although eclectic and innovative in terms of tonal and visual design, Leslie Smith's approach is inspired by the work of mid-19th-century Canadian and American firms such as S. R. Warren of Montréal and Hook & Hastings of Boston, favoring generous scaling and higher pressures.

Wooden pipes for these two instruments were made in-house, but metal pipes were supplied by F. J. Rogers, Leeds, England. Blowers came from Laukhuff, Germany. Keyboards, and key and stop action were fabricated in the shop. Stops are divided into bass and treble, using a special form of drawstop mechanism developed by the builder. Cases are made from common hardwoods, using traditional construction techniques.

Maintenance work to organs of all makes and construction in Ontario and Québec comprises a significant part of his activity; in 1996 he was appointed curator of the largest pipe organ in Montréal, a four-manual, 86-stop Casavant instrument (installed in 1932, rebuilt in 1992 by another firm) at the Church of St. Andrew and St. Paul, and will soon undertake complete rebuilding projects, as well.

The Future of Organbuilding

The status of organbuilding in the 21st century is not easy to predict, given the variety of factors involved. Generalizations about the number of future organ installations are risky; nevertheless, it is interesting to note that, within roughly the last three decades, while the annual production of instruments of all sizes peaked several times in the 1980s, the low periods of the 1970s were again matched in the years since 1994. Whether this recession will continue in the coming years is uncertain, but some recent trends provide clues to a possible future.13

The fact that few new organs have been installed in Canadian locations in recent years is not surprising, for the distinguishing characteristics of the "golden age" of the organ in the early years of the twentieth century--in terms of the erection of new church buildings, the proliferation of organbuilding firms that supplied both churches and motion picture theaters with instruments, and public enthusiasm for organ recitals played by local and touring recitalists--are not likely to be repeated, considering shifting cultural values along with the various musical and other forms of entertainment now available.

Although most organbuilders have confined their operations to meeting only local and regional needs, several Canadian firms have cultivated the international market with apparent success. The services of the Canadian Commercial Corporation, a crown corporation of the Government of Canada that assumes the role of prime contractor and subcontracts all of the contract back to the Canadian firm, are available for companies seeking worldwide clients.

As for the tonal design of new instruments, the uneasy hybrid designs of earlier years largely have been abandoned in preference to the rediscovered qualities of universally admired older instruments of the 17th and 18th centuries, without blindly copying them. Although instruments of neoclassical design, with their historically "authentic" stoplists, are not entirely suitable for the performance of all schools of organ music, they are probably more versatile than the earlier generation of organs for general liturgical and performance purposes. On the other hand, some organbuilders prefer an eclectic approach, a matter that is subject to ongoing debate.14 The recent strong demand for mechanical-action instruments may eventually stabilize, for reasons relating to architecture, economics, changing musical tastes, and a return to the Romantic idiom in repertoire. Purchasers may prefer some of the advantages of nonmechanical instruments, such as the consistent keyboard touch and flexible console location provided by electric action.15

Much of the earlier activity of new organ construction has been redirected to rebuilding and restoring older instruments, some of historical significance. Most Canadian organbuilders engage in this growing activity, which can provide churches with a cost-effective alternative to the purchase of a comparable new instrument. Routine maintenance work is also part of the service provided by many firms, large and small.

Pipe organs have always been expensive, so electronic instruments utilizing highly developed digital technology now provide an economic alternative for church congregations lacking the will or the means to acquire and maintain a pipe organ. The respective merits of pipe organs and electronic instruments have been debated since the latter were first introduced. Nevertheless, there is an obvious answer, based on musical criteria, to the question, Which is preferable: a poorly designed, badly maintained pipe organ, or a high quality electronic instrument? Electronic instruments have a place in locations where pipe organs are out of the question, whether for space or budgetary considerations. They have proved adequate for the liturgical requirements of many small or medium-size churches with limited budgets, and these instruments have provided competition for more costly pipe organs. The increasing acceptance of electronic instruments further diminishes the probability of a significant number of new pipe organ installations in the coming years. On the other hand, educational institutions (those that are not financially beleaguered, if any) and affluent congregations of some churches (not necessarily the largest) undoubtedly will continue to prefer pipe organs for musical, historical, or social reasons, and such instruments can be supplied only by the larger, well-established, organbuilding companies.

The role of the organist is of considerable importance in ensuring a future for organbuilding. If a church considering the purchase of a new organ already has a fully trained organist, this person, working with a musically educated and supportive committee, can influence the decision in favor of a pipe organ in preference to an electronic instrument, providing that a realistic fund-raising objective can be achieved. A church with an adequate pipe organ will seek a highly trained individual to play it, and such organists ordinarily prefer appointments to churches with pipe organs; once hired, their presence encourages the continuation of the pipe organ tradition.

Changes in the liturgical practices of some religious denominations may have a subtle, long-term effect on the future of organbuilding. The emergence in some congregations of youth-segregated services, with their unique liturgical practices that employ guitars or other instruments associated with folk music or religious rock groups, may produce a generation of worshippers unfamiliar with the organ, its musical heritage, and its literature. A broader associated issue is the question of the future of institutionalized religion and its possible decline due to the growth of science, education, and secularization, or its theological transformation into various manifestations of individualistic spiritual development. These possibilities undoubtedly will take many years, perhaps centuries, to resolve.      

Shifts in population characteristics introduce another factor into the question of the future of organbuilding. Some suburban churches located in stable neighborhoods now have congregations comprised largely of aging members living on limited incomes, not offset by significant numbers of younger, fully employed members. If the present job of organ maintenance is difficult for such congregations, even with skilled volunteer labor working under the supervision of a trained organ technician, the acquisition of a new instrument is beyond consideration; in fact, the amalgamation or dispersal of these congregations is the more likely scenario. The inevitable result would be the closing of some church buildings, along with the possible removal or relocation of existing pipe organs. The more affluent churches with a wider spread of ages among their members, and which encourage the full participation of younger members in their musical programs, are the only ones that will escape this fate, thus leaving open the possibility of the purchase of a new organ in the distant future. A related consideration, which provides a cause for optimism, is grounded in the speculation that recent declines in per capita real income may stimulate group activities at the expense of individual life styles, and that churches may again become a center of social as well as spiritual activities. In such contexts the pipe organ, as a cultural, religious, and artistic centerpiece, may serve as a source of pride and inspiration, and as a vehicle for the renewal of congregations.16

Over the longer term, increased public awareness, combined with both formal and informal educational opportunities, may contribute to the sustained vitality of the organ culture generally, including organbuilding. Radio broadcasts of organ recordings, instructive television programs, increased concert programming for organ and other instruments, and the development of audiences for subscription series of organ recitals, would increase knowledge of the organ among the general public. In the educational system, in-service sessions on the organ for school music teachers, the preparation of classroom learning materials for use in regular music instruction courses, and the participation of students in on-site inspection trips and demonstrations would provide practical contexts for raising awareness of the organ at a level that students can understand and enjoy.17 As for organists, competitions or commissions for hymn arrangements, sacred songs, or new compositions for the organ could be fostered on both the regional and national levels by the Royal Canadian College of Organists. These informational and educational programs would contribute to the development and maintenance of an appreciative audience for the organ throughout the coming decades. Such forms of revitalization would ensure the future of the King of Instruments well into the 21st century.

REFERENCES

                        13.              Some of the following material is adapted from the chapter, "The Future of the Organ," in Hartman, The Organ in Manitoba (note 5 above).

                        14.              See Quentin Regestein and Lois Regestein, "The 'Right' Organ," The Diapason, August 1998, 13-16; September 1998, 17-18. Radically opposing points of view debate the legitimacy of a "universal" hybrid organ, one that is perfect for everything.

                        15.              R. E. Colberd, "Pipe Organ Building: the Nineties and Beyond," The Diapason, July 1994, 12.

                        16.              Ibid., 14.

                        17.              For a description of a recent educational event for school children, see Valerie L. Hall, "Meet the King of Instruments: A Successful Workshop Model for Kids," Organ Canada, July 1998, 9.

Thomas Prentice Sanborn (1892)

Goulding & Wood, Inc. (2011)

Cook Grand Hall

Indiana Landmarks Center, 

Indianapolis, Indiana

Thomas Prentice Sanborn (1892)

Goulding & Wood, Inc. (2011)

Cook Grand Hall

Indiana Landmarks Center, 

Indianapolis, Indiana

Downtown Indianapolis is home to a number of architecturally distinguished churches from the last quarter of the nineteenth century. In addition to locations within the mile square of the city’s planned downtown, a few “sub-urban” churches line the periphery of the historic district. One of the latter is on Central Avenue, one of the city’s main conduits, a mile and a half from city center. Built as the Central Avenue Methodist Episcopal Church, the building was the second church to serve the congregation. Following a tornado that severely damaged the original wooden structure, the congregation began planning the current church in 1886. The cornerstone was laid on 12 September 1891, and the building was completed in the following year.

Central Avenue Methodist Church continued to grow in the early part of the twentieth century, and by the 1920s it was the largest Methodist congregation in the state of Indiana. Accordingly, it played a large role in local Methodism, and two of its pastors later became presidents of DePauw University in nearby Greencastle, Indiana. Although the changing demographics of the neighborhood brought a steady decline in membership in the second half of the twentieth century, the striking architecture of the building and the ardent commitment of the membership maintained the church as an important institution in downtown Indianapolis. 

The church interior follows the Auditorium Plan popular in mainline Protestant churches in the last quarter of the nineteenth century. The original intent of this architectural design was providing a speaker with unobstructed visual and aural access to a large number of people. The sanctuary achieves this admirably; even without electronic amplification, a speaker in the pulpit can be heard clearly throughout the 1,300-seat room. Curved walls, a rigid dome ceiling, and avoidance of absorptive material all contribute to the efficacy of the acoustics for this purpose. The room is then finished in an appropriate and aesthetically pleasing manner, with graceful carved elements in the chancel furnishings and pews and elegant stained glass windows. The organ, which stood behind the pulpit, shares the most prominent position in the room, visually and acoustically. Although the room is clearly designed for worship in the mainline, non-liturgical Protestant tradition, it also supports musical performance involving the pipe organ. 

The pipe organ was present at the dedication of the building in 1892, with indications that the instrument was new rather than retained from the previous building. The prior church building held an organ built by William H. Clarke & Co. of Indianapolis, and this organ had been relocated there from another house of worship. The organ in the new 1892 church was misattributed to Clarke for many years, and identification of the builder was further clouded by the fact that after less than thirty years of service, the organ’s mechanics were significantly altered. Any builder’s plate or other placard naming the builder seems not to have survived this project. Several identifications within the organ led conclusively to identifying the builder as Thomas Prentice Sanborn. 

Sanborn worked as the shop foreman for William Clarke, and it makes sense that he would have been familiar with the church. Unfortunately, little is known about Sanborn other than the fact that he did go on to work under his own name at a shop on Massachusetts Avenue, the same address of Goulding & Wood. It is unclear how many organs he built after he left Clarke, and only one other extant instrument is known to be by him. Sanborn did sign many of the pipes in the organ, either with his full name or his initials, a practice he did not follow on instruments he built with Clarke. 

The organ is quite large for its time, and it has many classical elements that were atypical of late-nineteenth century tastes. Both divisions feature complete principal choruses, including mixtures. The Great chorus is based on 16′ pitch, and the Swell on 8′ pitch. The stoplist includes a wide variety of flutes, both stopped and open, as well as an interesting choice of reed stops. The manual compass is 61 notes, which was quite forward looking, while the Pedal compass is much more typical of its time, with a 27-note span. It is tempting to imagine that Sanborn was eager to make a bold impression with this well-designed and robust organ. Perhaps he even thought of it as a crowning achievement, a testament to his skill, as well as a calling card to attract more customers. 

In 1921 the church engaged the Seeburg-Smith Co. of Chicago to modify the mechanics of the organ to employ electrical switching. Justus Percival Seeburg was a Swedish-born piano maker and Frederick W. Smith was an English-born organ builder who apprenticed with Robert Hope-Jones. Their partnership, which lasted from 1916 to 1921, combined Seeburg’s skills as a piano builder and Smith’s knowledge of contemporaneous English organ building, equipping them for building and maintaining theatre organs, player pianos, and orchestrions. Evidence of their work on church organs is sparse, and the timing of the Indianapolis project near the dissolution of their firm may imply that they were willing to accept work outside their focus since the firm was in trouble. They removed all of Sanborn’s console controls and whatever actuating system interfaced with the windchest mechanics. In their place, they installed a cumbersome electrical switching system and electro-pneumatic action for the chest mechanics. They also installed a new detached console that is not extant. Their work shows a fair degree of competency and care, although the design of their mechanical systems lacked responsiveness, reliability, and sensitivity. 

The congregation at Central Avenue UMC dissolved in 2006, and the unused room fell into disrepair until Indiana Landmarks, a historical preservation foundation, took interest in the building. Bloomington, Indiana philanthropists William and Gayle Cook funded a comprehensive restoration project, including completely refurbishing the interior and exterior of the church along with the pipe organ. The building now serves as a civic performance space and as Indiana Landmarks’ headquarters. In 2010 Bill Cook and Indiana Landmarks chose Goulding & Wood to carry out a project to bring the organ back into usable condition.

The first step in reviving the organ was to assess its history and current condition. The sole known photographic documentation of the installation prior to any alteration does not depict the console controls with any usable clarity. One of the first questions, then, was the original placement of the console in relation to the organ case. Nineteenth-century organs typically have keydesks en fenêtre, that is, placed within the apron of the instrument’s front façade case. Given that Thomas Prentice Sanborn was a local builder of limited accomplishment, it is unlikely that he would have had the technological proficiency to engineer a detached mechanical console. On the other hand, the façade paneling in the apron seems to be original. There is no visible sign of alteration in the central panel, and its carving detail, wood grain, stain, and condition match exactly the panels on either side. If the organ initially had a keydesk en fenêtre, the central panel must have been entirely replaced. Given the quality of the first renovation work from 1921, it seems unlikely that the Seeburg-Smith Company had the woodworking resources to match the rest of the paneling with such precision. 

If the console controls were remote from the main body of the organ from the beginning, and if the mechanical engineering required of a mechanical action arranged thus would have been beyond Thomas Sanborn, the natural conclusion is that the organ was never purely mechanical. Sanborn is known to have been awarded a U.S. patent No. 465,208 for a valve mechanism that was a mechanical-pneumatic assist, facilitating playing keys that operate large pallet valves from a distance that would otherwise cause heavy action. Such pneumatic assists were somewhat common in the late nineteenth century as organ builders endeavored to make instruments of unprecedented size and in arrangements that would have been impossible for purely mechanical key action. Another pre-electrical innovation to address these issues was tubular pneumatic action, whereby key action is conveyed to the pallet and slider windchests via lead tubes. Due to the complicated and elaborate nature of this action, plus its dependence on lead for semi-flexible tubing, this system remained in use for a very short period. 

Although the other known Sanborn organ is a tracker instrument, it is entirely possible that he would have had an awareness of tubular pneumatic organs. Indeed, given the implication of his mechanical leanings as suggested by his procurement of a patent, Sanborn may have had motivation to employ the most recent design technology in such a prominent instrument. Unfortunately, the restoration project yielded no evidence in the organ that either proves or disproves the original actuating mechanism. One can only surmise, given the apparent placement of the console and the size of the organ, that a purely mechanical installation was never in place. 

The Seeburg-Smith electro-pneumatic actuating system was obviously a retrofitted attempt to incorporate electricity into the action of the organ. Aside from telltale signs such as a difference in wood species used, the interface between the Seeburg-Smith mechanics and the Sanborn mechanics was clumsy and contrived. This work was done near the advent of using electricity in organs, and the action has a rudimentary design. The practice of retrofitting an improvised action onto tracker action chests was somewhat common during this period, but rarely was the attempt successful. The tolerances of the added action are so slight, a product of working within a predetermined spacing of the existing chest, that the new actuating systems rarely operate the chest actions properly. It is likely that the Seeburg-Smith mechanics never worked entirely satisfactorily, although they did permit the use of electrical key contacts in the console, thus reducing the weight of the keys for organists. In sum, however, these components compromised the organ’s action. 

With restoration of the original chest action impossible, Indiana Landmarks elected to replace the windchests. Goulding & Wood’s electro-pneumatic slider chest design shares much in common with tubular pneumatic action, in that a traditional chest grid interfaces with remotely actuated pallets and sliders. This choice then restored the instrument to a similar musical condition, as pipes receive wind much as they did originally.

On early site visits a harp stop was discovered, although no written documentation of such an addition has been found. Given the wood species and stain color, it seems that this unit was installed with the other Seeburg-Smith components. Seeburg-Smith built theatre organs and orchestrions, thus the addition of a harp is solidly in line with their main output. While it is clearly not original to the organ, the donor and oversight committee elected to retain this interesting addition. Fellow Indianapolis organ builder Carlton Smith Organ Restorations refurbished the 37-note harp unit.

The pipework throughout the organ was in reasonably good condition, considering the age of the instrument. Most of the pipes were cone tuned, and a century of routine maintenance had taken its toll on the tops of most of the pipes. Surprisingly, most of the scroll-tuned pipes were in very good condition, and in general, the pipes were well built and very well racked. 

Work began in February 2010 with the removal of the organ. The building had no heat or power, and the roof was collapsing. The Goulding & Wood crew, led by Mark Goulding, thus worked in heavy winter coats using only flashlights for illumination. In the following year, each pipe was washed, given new tuning sleeves, and regulated by G&W voicer Brandon Woods. The organ was preserved tonally, with only two slight pedal additions. The original specification included no independent pedal reed despite a large manual disposition including four reed stops. Goulding & Wood recommended extending the three original pedal stops from 27 to 30 notes and adding a metal-resonator 16′ Trombone built by A. R. Schopp’s Sons, Inc.

From the photograph of the church that was taken in 1910, it is clear that the display pipes were originally stenciled. They were subsequently painted a solid gold color on the front half of the pipes, but the original stenciling was still observable along the edges of the newer paint. Conrad Schmitt Studios of Milwaukee, the firm responsible for restoring the sanctuary interior, re-stenciled the pipes and added gold leaf.

Goulding & Wood restored all of the original casework, re-staining and toning the woodwork with only minor repairs required. The crew extended the apron paneling, including the whimsical carved motif, on either side to accommodate room modifications and constructed matching podiums for the platform. Staff draftsman Kurt Ryll designed a new two-manual console patterned after extant consoles from other tubular-pneumatic organs. The terraced layout and richly ornamented cabinet lends a strongly contemporaneous appearance, defying the anachronistic solid-state control system provided by Solid State Organ Systems. 

As with all new organs by Goulding & Wood, the entire instrument was set up in the shop for testing and regulation. Given the heavy local interest (the church is less than a half mile from the shop), many visitors stopped in to see the progress, and the shop hosted festive open houses once the organ was playing. 

With room renovations complete, Goulding & Wood reinstalled the organ in spring 2011 in time for the facility’s grand opening. Many celebratory events marked the entire project, and the organ was featured in many varying roles. Sadly, Bill Cook, the donor whose vision and generous financial backing made the project a reality, passed away days before the dedicatory events. Tributes to the Cook family, all of whom are long-time patrons of historical preservation, took on added significance during the celebrations in the newly renamed Cook Grand Hall.

Although the activity inside the building has changed dramatically over the past century, its place as an anchor to the wider community continues. Cook Grand Hall is now a venue for concerts, recitals, weddings, and other community events. Many functions feature the organ, which contributes its unique and colorful voice as an echo from Indiana’s past. Through such public prominence, the instrument is also contributing to the future of the pipe organ in the cultural life of the city.

—Jason Overall

Cover photo: Susan Fleck Photography

Matthew M. Bellocchio, a Project Manager and designer at Andover Organ since 2003, is a Fellow and past President of the American Institute of Organbuilders.

Andover Organ Company marks seventy years

by Matthew M. Bellocchio

Anniversaries invite us to reflect upon our past and contemplate how far we have come. As 2018 marks Andover Organ Company’s seventieth anniversary, this article will highlight its long and rich history, from its humble beginnings to its recent achievements.

Andover was founded in 1948 as a result of an Organ Institute organized by Arthur Howes, head of the organ department at the Peabody Conservatory, and held each summer on the campus of Phillips Academy in Andover, Massachusetts. Howes had traveled extensively in Europe and observed the developing Organ Reform Movement there. Originating in Germany in the 1930s from Albert Schweitzer’s writings, the movement sparked an interest in early music and performance practices, as well as the building of new organs that could authentically render early music, especially that of Bach. Howes started the Organ Institute to help spread the Organ Reform Movement in America. The faculty included such notable organists as Carl Weinrich (Princeton University), Ernest White (St. Mary the Virgin, New York City), and E. Power Biggs.

Tom Byers, a former Henry Pilcher’s Sons Organ Company employee who lived in nearby Lawrence, Massachusetts, attended the annual institute with his wife. He was inspired to start an organ company that would follow the institute’s philosophy. He chose the name “Andover” for its prestigious association with the Organ Institute and because of the advantages, in the pre-internet days of telephone directories, of appearing near the top of the alphabetical company listings. 

Byers chose the opening line of Psalm 98, “Cantate Domino Canticum Novum” (Sing to the Lord a New Song), as the company motto, which still appears on Andover’s letterhead. This underscored his philosophy of creating a new style of organ, one that looked and sounded differently from what most American organ companies were producing.

Despite its name, the company has never been located in Andover! It started out in the home of Tom Byers in Lawrence, just north of Andover, and later moved to a two-story wooden building in nearby Methuen. In 1979 the company purchased a three-story brick building in a former mill complex at 560 Broadway in Lawrence, where it has been ever since.

Leadership and people

Rather than having a single leader dictate the company’s course, Andover’s many talented employees have each contributed to the company’s development. The company has always been owned and run by its principal employees who, serving as its shareholders and board of directors, make decisions collegially.

Charles Fisk joined the company in 1955 as Tom Byers’s junior partner. Robert J. Reich, a Yale-trained electrical engineer, was hired in 1956, and Leo Constantineau, a woodworking teacher and professional draftsman, in 1957. In 1958, Byers left the company, and Fisk became the owner. Walter Hawkes, who had worked for Holtkamp, was hired as shop foreman. Later that year, Andover signed a new organ contract with Redeemer Lutheran Church in Lawrence, Massachusetts. The contract did not specify the type of action. But the result, premiered on Palm Sunday 1959, was the first new mechanical-action organ built by an American firm in the postwar era. That instrument, Opus 28, is still in use.

The following year, Opus 35, a 33-stop tracker designed by Leo Constantineau and voiced by Charles Fisk, was built for Mount Calvary Episcopal Church in Baltimore, where Arthur Howes was organist. Fisk left Andover in 1961 to start his own company,
C. B. Fisk, in Gloucester, Massachusetts. Andover was reincorporated with Robert J. Reich and Leo Constantineau as the new owners. Reich, who became the Tonal Director, revised Andover’s pipe scales to provide more foundation tone. Constantineau’s case designs gave the company’s new instruments a distinctive visual flair. 

Andover has been blessed with several dedicated individuals who each worked over fifty years at the company. Reich, who joined Andover in 1956, served as President and Tonal Director 1961–1997; he then worked part-time until retiring in 2009. Donald Olson joined the company in 1962 and became Andover’s general manager and visual designer in 1968. His elegant case designs were the hallmark of Andover’s new instruments for nearly four decades. He succeeded Robert Reich as President in 1997, stepped down in 2012 and then worked part-time until fully retiring in 2015. Robert C. Newton, who started at Andover in 1963 and headed the Old Organ Department for many years, retired in 2016.

Andover’s current President, Benjamin Mague, joined Andover in 1975. He holds a Bachelor of Arts degree in music from Colby College and a Master of Music degree in organ from the University of Wisconsin. He served as Andover’s mechanical designer and later as shop foreman before becoming President in 2012. 

John Morlock, Andover’s Tonal Director since 1999, joined the company in 1976, working principally in the Old Organ Department. Don Glover, Andover’s in-house reed voicer, came to Andover in 2004 from the Reuter Organ Company.

Michael Eaton, Andover’s visual designer, joined the company in 1991. He also heads a maintenance team and serves as Treasurer and Clerk for Andover’s board of directors.

Andover’s present team of dedicated and talented people collectively possess over 350 years of organbuilding experience. Other current employees are Ryan Bartosiewicz, Matthew Bellocchio, Eric Dolch, Anne Doré, Andrew Hagberg, Lisa Lucius, Kevin Mathieu, Fay Morlock, Jonathan Ross, Craig Seaman, and David Zarges. Appropriately, more than half of Andover’s employees are church musicians or organists.

Andover has been the parent for many other New England tracker organ companies, having employed over its seventy years many talented individuals who later founded their own companies. These include Philip Beaudry, Timothy Fink, Charles Fisk, Timothy Hawkes, Richard Hedgebeth, Fritz Noack, Bradley Rule, J. C. Taylor, and David Wallace.  

Tonal style

Tonally, the early Andover organs were inspired by the Organ Reform Movement. At the time of Andover’s founding, few American companies were repairing old tracker organs; most just electrified or replaced them. Andover was the first to deliberately retain and renovate nineteenth-century trackers. But, adhering to the Organ Reform philosophy, Byers and his early successors often “improved” those organs tonally. It was not unusual for them to evict the string stops and replace them with mixtures and mutations. Andover’s new instruments came to be characterized by strong Principal choruses with bright mixtures, colorful neo-Baroque style flutes and mutations, and reeds that emphasized chorus over color. 

In the 1980s, as Andover began more frequently to work on significant nineteenth-century American organs, a gradual transition occurred. This was solidified in 1999 when John Morlock, who had started in Andover’s Old Organ Department, succeeded Robert Reich as Tonal Director.

Today, Andover’s tonal style may best be described as “American” and is grounded primarily in the best practices of the nineteenth-century New England builders, in particular the Boston firm of E. & G. G. Hook. Their organs, especially those from the firm’s “golden period” (1850s to 1870s), are admired for their remarkably successful blend of warmth and brilliance. Their pipe scales and voicing techniques worked extremely well in the dry acoustics of many American churches. 

When designing a new organ or reworking an existing instrument, we basically use the same scaling proportions between the various stops of the chorus that the Hooks used. We have found that doing so results in a principal chorus that is nicely balanced between fundamental weight and harmonic development.

Within this framework, adjustments are made to reflect or, in some cases, compensate for the acoustical properties found in each room. Each instrument needs to work and sound well in its “home” and be able to perform its tasks capably and effectively. Andover organs are designed to lead and support congregational hymn singing, as well as interpret a wide range of organ literature.

Maintenance

From the very beginning, organ maintenance was an important part of the company’s work. It created name recognition, established relationships with churches and organists, and provided a consistent revenue stream. Today, Andover maintains over 300 organs annually throughout the Northeast, Mid-Atlantic, and Southeast—from northern Maine to South Carolina, from western New York to the islands off eastern Massachusetts. These instruments range in size from small one-manual trackers in country churches to the world-famous Great Organ (IV/116) in the Methuen Memorial Music Hall; and range in age from a few years to a historic 1762 Snetzler organ. 

We service all types of organ mechanisms—from traditional tracker action to modern solid-state relays and combination actions. Each spring and fall, we schedule extended maintenance tours to visit multiple instruments in a geographical area. This enables our customers to share the travel expenses. 

Many customers treat us like old friends. Occasionally, a church secretary or organist will call us and merely say, “This is so-and-so at First Parish Church,” not realizing that we have over three dozen tuning customers with that name!

Andover Organ firsts

As the leader in the mid-twentieth century tracker organ revival in America, Andover pioneered many innovations that are now standard in the industry. Opus 25, a two-manual built in 1958 for the Rice Institute (now University) in Houston, was an electro-pneumatic instrument utilizing slider chests with pneumatic pallets, one of the first examples of this pallet type. This was decades before the adoption of the “Blackinton-style” pneumatic pallet.

In 1961, Andover carried out the first historically sympathetic restoration of a nineteenth-century American organ: the 1-manual, 1865 E. & G. G. Hook Opus 358 at the Congregational Church in Orwell, Vermont (Andover Opus R-1.)  

Other significant Andover (AOC) restorations include: 

• First Presbyterian Church, Newburyport, Massachusetts (1866 E. & G. G. Hook/AOC 1974); 

• First Parish Church, Bridgewater, Massachusetts (1852 E. & G. G. Hook/AOC 1977); 

• South Parish Congregational Church, Augusta, Maine (1866 E. & G. G. Hook/AOC 1982); 

• Church on the Hill, Lenox, Massachusetts (1869 William A. Johnson/AOC 2001); 

• Old Whaling Church, Edgartown, Massachusetts (1850 Simmons & Fisher/AOC 2004); 

• Centre Street Methodist Church, Nantucket, Massachusetts (1831 Thomas Appleton/AOC 2008); 

• St. Peter’s Catholic Church, Haverstraw, New York (1898 Geo. Jardine & Son/AOC 2011); 

• St. Anna’s Chapel, Newburyport, Massachusetts (1863 William Stevens/AOC 2013).

Utilizing its expertise gained from restoring old tracker organs and building new ones, in 1963 Andover was the first company in the world to re-trackerize an old tracker organ that had been electrified. The instrument was the 1898 James Treat Opus 3 at St. George’s Primitive Methodist Church (now Bethesda Missionary Church) in Methuen, Massachusetts.

Other notable re-trackerizations: 

• First Presbyterian Church, Waynesboro, Virginia (1893 Woodberry & Harris/AOC 1986); 

• St. John’s Episcopal Cathedral, Providence, Rhode Island (1851 E. & G. G. Hook/AOC 1989); 

• Westminster Preservation Trust, Baltimore, Maryland (1882 Johnson & Son/AOC 1991); 

• Sage Chapel, Northfield, Massachusetts (1898 Hook & Hastings/AOC 1996); 

• Unitarian Society, Peterboro, New Hampshire (1867 E. & G. G. Hook/AOC 2003); 

• Christ Episcopal Church, Charlottesville, Virginia (1869 E. & G. G. Hook/AOC 2012).  

The slider and pallet windchests used in most nineteenth-century organs were generally trouble free for many years. However, when heating systems were introduced into churches in the early twentieth century, problems developed. The solid wood chest tops (tables), just below the sliders, were made from a thin, wide plank of air-dried lumber. With constant heating the wooden tables dried out and cracked, allowing air to leak from one pipe hole to the next, resulting in “runs.” 

Andover was the first American company to replace a cracked, solid-wood table with a marine-grade plywood one. The routed bleed channels between the table’s wind holes were then carefully replicated and the entire table graphited, like the original. This type of table replacement is now standard in the industry. The first organ to receive this treatment, in 1965, was the 1897 George W. Reed, at the Baptist Church in Winchendon, Massachusetts. Sadly, the organ burned with the building in 1985. 

One of Andover’s most significant recent projects was the 2016 restoration of the wind system and key action in the 1892 Woodberry & Harris Opus 100 at St. Mary–St. Catherine of Sienna Parish in Charlestown, Massachusetts. With three manuals, 36 stops, and 41 ranks, it is the largest and most significant nineteenth-century organ remaining in original unaltered condition in the greater Boston area. 

The instrument’s action is entirely mechanical and incredibly complex. The three-manual, reversed detached console sits in the center of the gallery, while the pipes and windchests are in cases at either side of a large stained-glass window. Four levels of trackers descend from the keys to squares beneath the floor, then under the console towards the rear window, then turn off at right angles towards the sides, then turn off again at right angles towards the rear, then to squares which send them up to the rollerboards below the chests. The organ’s four divisions have a total of 17 sets of wooden trackers, totaling nearly a mile in length! A Barker machine lightens the touch of the Great and the manuals coupled to it.

The two large reservoirs were stripped and releathered in place. All four layers of trackers were disassembled, labeled, and brought to the shop for replication. Because of the organ’s historic significance, all the new trackers were made of the same materials as the originals but using modern machinery. Andover customized a miniature CNC router to notch the cloth-wrapped tracker ends and built a spinning machine to whip the threaded wire ends with red linen thread, just like the originals. The Barker machine was carefully releathered. “Now she runs like a Bentley,” said one of the instrument’s many admirers.

Rebuilding for reliability

A conservative restoration is the logical decision for an exemplary work by an important builder or a small organ in a rural church with modest musical requirements. But sometimes it is necessary to strike a balance between preserving the original fabric and updating it to suit modern needs. An organ that has already endured several unsympathetic rebuilds, or an aging instrument with unreliable mechanisms and limited tonal resources, in an active church or institution with an ambitious music program might be better served by a sympathetic rebuilding. This was the case with two of Andover’s most significant rebuilds.

The 1876 E. & G. G. Hook & Hastings Opus 828 at St. Joseph Cathedral in Buffalo, New York, was built as a showpiece for the 1876 “Centennial Exposition” in Philadelphia and purchased afterwards by the cathedral. Major changes were made to the organ by Tellers-Kent Organ Company in 1925 and by Schlicker Organ Company in 1976. By 1996, the organ was virtually unplayable during the winter months and a decision of whether to replace it or rebuild it was imminent. In 1998, the cathedral decided that “the organ need not be replaced, but rather completely rehabilitated.” At the same time, the organ’s tonal palette needed expanding to better serve the musical needs of the cathedral and to enable it for use in concerts and recitals.

A team from Andover dismantled the organ in July 1999, loaded it into two moving vans, and transported it back to Lawrence, where eighteen employees labored for more than a year to clean, repair, and expand the instrument. In undertaking this immense job, Andover sought to retain and restore as much of the original as possible. The entire organ was cleaned, and the black walnut case stripped of coats of dark varnish and restored to its original finish. The façade pipes were stripped and repainted in their original designs with colors that harmonized with the cathedral’s interior.

All the original chests and pipework were rebuilt and repaired. The manuals were expanded to 61 notes and the pedals to 32. The two original reservoirs were releathered and two new ones constructed. The Choir is now unenclosed, as it originally was, the Swell box is back to its original size, and the Solo is restored to its original position.

Many of the missing original pipes were replaced with pipes salvaged from the Hook 1877 Cincinnati Music Hall organ, Opus 869. Other compatible Hook organs were visited to develop pipe scales appropriate for the additions to the cathedral organ, which were voiced in the Hook style. The organ is now far closer to its original sound than it has been since the 1923 electrification and rebuilding.

A new floating Celestial Division on a slider windchest was added. This division was based on contemporary E. & G. G. Hook solo divisions, as typified by the organs in the Cincinnati Music Hall and Mechanics Hall, Worcester. There is an 8′ Philomela copied from the 1863 Hook at Church of the Immaculate Conception in Boston, an original Hook 4′ Hohlpfeife, a 2′ Harmonic Piccolo, a Cor Anglais, and a few more modern stops stops such as a French Horn, Dolcan Gamba with Gamba Céleste, Spitzflöte and Spitzflöte Céleste. 

Thomas Murray played the rededicatory recital on June 11, 2001. The St. Joseph Cathedral organ will be featured in a recital by Nathan Laube during the American Guild of Organists Northeast Regional Convention, July 1–4, 2019.

In contrast to the Buffalo cathedral organ, the 1902 Hook & Hastings Opus 1833 at St. John’s Seminary in Brighton, Massachusetts, was a modest two-manual, 18-rank instrument. After nearly a century of use and constant winter heating, the windchests and actions developed serious problems. The original console was replaced in 1946. When the replacement console failed in 2004, a one-manual tracker was put in its place to serve as a temporary instrument until the chapel organ could be rebuilt. 

Our lengthy experience with Hook & Hastings organs taught us that their early electro-pneumatic actions were cumbersome, slow, and difficult to repair. Therefore, in our 2014–2015 rebuilding of the organ, we reused the pipes, windchests, and most of the original parts as the basis of an expanded instrument with a new electric action.

We built a new, solid white oak console in the style of the Hook & Hastings original, with a lyre music rack and elliptically curved stop terraces. To meet the demands of a twenty-first century music program, this reproduction console has state-of-the-art components, including a record/playback module. The façade pipes were stripped and repainted with a new decorative treatment that harmonizes with the Italian Renaissance-style case and chapel. As a crowning flourish, the cross surmounting the case was painted in faux lapis lazuli.

Most of the organ was crammed within the small case, with Swell above Great and the wooden Pedal 16′ Open Diapason pipes at each side. Behind the Swell, in an unfinished gallery, were the organ’s large reservoir and Pedal 16′ Bourdon. We moved the Pedal Open Diapason pipes to the rear gallery and added a Pedal 32′-16′-8′ Trombone and 8′-4′ Principal there. Judicious additions to the Swell expanded its resources. There was sufficient space inside the case behind the Great chest to add a seven-stop unenclosed Choir division.

The end result of these tonal changes and additions is an instrument of 40 stops, 34 ranks, and 1,994 pipes that is more versatile and appropriate for its expanded role. It still sounds very much like a Hook & Hastings organ, but one from an earlier and better period of the firm’s output.

Façade firsts

The company’s work with historic organs gradually led to pipe façade restorations as well. In 1967, Andover was the first American company to make restorative paint repairs to a painted and stenciled pipe façade, at the First Congregational Church in Georgetown, Massachusetts (1874 Joel Butler). Thirteen years later, in 1979, during its rebuilding of the 1884 Geo. S. Hutchings Opus 135 at the Vermont College of Fine Arts in Montpelier, Vermont, Andover carefully stripped a coating of green paint from all the façade pipes, documented the original designs and colors underneath, and repainted the pipes in their original colors and stenciling—another first.

Andover’s Opus 102 (1992) at Trinity United Church of Christ in York, Pennsylvania, was the first new American organ in the modern era to feature painted façade pipes with nineteenth-century style colored bandings. The upper façade flats of this organ contained another first: “frosted tin” pipes, which feature the natural, unplaned finish of the cast tin sheets. This gives them the light color of tin, but with a dull, non-reflective finish.

In recent years, Andover has worked with historic painted decoration conservator Marylou Davis to create new painted-pipe decorations in historically inspired styles. The most notable example of this collaboration is the 82-rank Andover Opus 114 (2007) at Christ Lutheran Church in Baltimore. This was the first twenty-first century American organ façade to combine polychromed and monochrome texture-stenciled pipes, frosted tin pipes, and numerous hand-carved pipe shades, grilles, finials, and skirtings in the casework. 

Opus 114 is also Andover’s first dual-action, double organ. The 13-rank, electric-action gallery organ can be played from its own console or from the front organ’s three-manual mechanical-action console. Likewise, the entire front organ can be played from the two-manual gallery console through couplers and general pistons. The organ’s four matching cases (two in chancel, two in gallery) perfectly suit the church’s Gothic architecture and fool many people into thinking that they were reused from a 19th-century organ. 

Andover has never been afraid to fit an organ around a prominent window. This reflects our design philosophy that an organ should look as if it has always been part of its environment. And in most churches, the window was there long before the organ. Fighting the window can sometimes be a losing battle. Opus 115 (2007) at Church of the Nativity in Raleigh, North Carolina, and Opus 118 (2014) at First Parish Church in Wayland, Massachusetts, illustrate Andover’s creative approach in dealing with windows.

In Raleigh, the modern clear glass window was front and center, at the top of the space where the organ would go. We designed the organ case to frame the window’s central orb and cross. The polished tin façade pipes match the brightness from the window. The organ also serves as a reredos for the altar, which stands in front of it. Looking from top to bottom, one sees the window, the organ, and the altar—light, music, action. The church was very pleased with the result, as were we.

In the 1820 Federal Period meetinghouse in Wayland, there was an elegant Palladian window in the center of the back wall of the rear gallery. Because of the semi-elliptical curve of the gallery’s rear wall, the only apparent organ placement with such a floor plan was in the center. Thus, all the previous organs had blocked the window. Andover’s design put the detached console in the center, by the railing, and divided the organ into two cases that frame, rather than cover, the Palladian window. The choir members sit in the space between the console and cases and benefit from the natural backlighting provided by the window. Again, everyone was pleased with the results.

Seventy years after its humble beginnings, Andover has much to celebrate: 118 new organs and 533 rebuilds/restorations. Andover’s wide-ranging work in building, rebuilding, restoring, and maintaining pipe organs is well-recognized, and best summarized by its mission statement: “Preserving the Past; Enhancing the Present; Inspiring the Future.”

www.andoverorgan.com